Patton electronic 4830 manual Additional information

Page 51

SmartNode 4830 Getting Started Guide

4 • Getting started with the SmartNode

 

 

Load a new application image (SmartWare) via the serial link

The Bootloader supports the ‘X-Modem’ and ‘Y-Modem’ protocols to download application images via the serial link of the console. Do the following to initiate the download:

Step

Command

Purpose

 

 

 

1

RedBoot> load -r -v -m {

Downloads an application image into the volatile memory

 

xmodem ymodem } -b

(RAM) from where the SmartNode could directly execute it.

 

base_address

‘xmodem’ or ‘ymodem’: Specify the protocol to be used, X-

 

 

Modem or Y-Modem

 

 

base_address: memory location where to store the application

 

 

image. Use the default address 0x1800100

 

 

Execute the above RedBoot command first, then start the trans-

 

 

fer from the terminal program with the command ‘Send file via

 

 

X-Modem’ (or similar).

 

 

 

5

RedBoot> fis delete -n 1

Deletes the first application image.

 

 

Reply with ‘y’ to the confirmation request.

 

 

 

6

RedBoot> fis create

Stores the downloaded application image to the permanent

 

 

memory (flash:).

 

 

Reply with ‘y’ to the confirmation request.

 

 

 

7

RedBoot> fis list -l

Checks whether the image has been successfully stored,

 

 

whether it is the desired Release and Build, and whether it is

 

 

valid.

 

 

 

8

RedBoot> go

Starts the application image that was downloaded to the vola-

 

 

tile memory (RAM).

 

 

 

Note This type of download takes about 25 minutes since it uses a serial link at only 9600 bps.

Additional information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting, refer to the Software Configuration Guide on the enclosed CD-ROM or the Patton website at www.patton.com. On the CD you will also find numerous freeware applications such as a TFTP server.

Additional information

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables About this guide AudienceStructure Impaired functioning PrecautionsSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions SmartNode 4830 Getting Started GuideAbout this guide General information Chapter contentsSmartNode product SmartNode 4838 shown SmartNode Model 4830 Series OverviewGeneral information Examples of SN4830 Series rear panels FXS only SmartNode 4830 Series Detailed DescriptionModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Multiservice carrier access over leased lines IntroductionApplications for SmartNode 4830 Series Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist Site log Network informationIP related information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Changing the IP address LoginLoad configuration Connect the SmartNode to the networkStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information EMC compliance Safety complianceCompliance Radio and TV Interference FCC PartIndustry Canada Notice FXO ports FCC Part 68 Acta Statement FXO portsAuthorized European Representative CE NoticeAppendix B Specifications T1/E1 interface if applicable Voice connectivityEthernet interface Sync serial interface if applicableShdsl Daughter Card if applicable Adsl Daughter Card if applicableFax and modem support Voice processing signaling dependentVoice signaling PPP and Frame-Relay supportIP services Voice routing-session productManagement Operating environment DimensionsWeight and power dissipation Power supplySmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Serial console Connecting a serial terminalEthernet straight-through Ethernet 10Base-T and 100Base-TAnalog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketDSL T1/E1Appendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portSerial port Sync Serial PortFXO port FXS portADSL/G.SHDSL port T1/E1 portAppendix E SmartNode 4830 Series factory configuration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Verified by Date Appendix G Accessories Description Part Number

4830 specifications

The Patton Electronics 4830 is a robust and versatile device designed for reliable communication in various networking environments. This product is a part of Patton's extensive portfolio, known for its quality, reliability, and innovative solutions in the telecommunications field. The 4830 model is primarily used for connecting Ethernet networks over long distances, leveraging advanced technologies to ensure optimal data transmission and connectivity.

One of the key features of the Patton 4830 is its support for both TDM (Time Division Multiplexing) and Ethernet over existing copper or fiber infrastructure. This functionality allows users to maintain legacy connections while upgrading their networks, providing a seamless transition to modern digital communications. The device supports multiple interfaces, including Ethernet, serial, and analog, making it suitable for diverse applications ranging from industrial automation to enterprise networking.

The 4830 is equipped with Patton’s SmartLink technology, which enhances performance by automatically optimizing the link conditions. This proprietary technology enables the device to adapt to varying network conditions, ensuring minimal downtime and maintaining high data integrity. Furthermore, the 4830 features built-in redundancy capabilities, ensuring that critical communications remain uninterrupted even in the event of a failure.

In terms of physical characteristics, the Patton 4830 is designed for rugged environments, featuring a compact form factor that allows for easy deployment in various settings. The device comes with LED indicators for power, status, and connectivity, providing real-time feedback to users. It can be mounted on a rack or installed on a desktop, making it a flexible option for different installation scenarios.

Another significant characteristic is its security features, which include firewall protections and encryption options to safeguard data against unauthorized access. This is particularly important for businesses that handle sensitive information and require compliance with data protection regulations.

With its combination of advanced functionalities, interoperability, and robust design, the Patton Electronics 4830 stands out as a reliable choice for organizations looking to enhance their communication capabilities while securing their network investments. As technology continues to evolve, the versatility of the 4830 ensures that it remains a relevant and effective solution for years to come. In summary, the Patton 4830 is an exemplary device that encapsulates the brand’s commitment to quality and innovation in telecommunications.
Top Page Image Contents