Patton electronic 4830 manual Specifications

Page 6

SmartNode 4830 Getting Started Guide

	CE Notice	62
	Authorized European Representative	62
B	Specifications	63
	DSP	64
	Voice connectivity	64
	Ethernet interface	64
	Sync serial interface (if applicable)	64
	T1/E1 interface (if applicable)	64
	ADSL Daughter Card (if applicable)	65
	G.SHDSL Daughter Card (if applicable)	65
	PPP and Frame-Relay support	66
	Voice processing (signaling dependent)	66
	Fax and modem support	66
	Voice signaling	66
	Voice routing—session product	67
	IP services	67
	Management	67
	Operating environment	68
	Operating temperature	68
	Operating humidity	68
	System	68
	Dimensions	68
	Weight and power dissipation	68
	Power supply	68
	Identification of the SmartNode devices via SNMP	69
C	Cabling	70
	Introduction	71
	Serial console	71
	Ethernet 10Base-T and 100Base-T	72
	Analog FXS	73
	Analog FXO	74
	T1/E1	75
	DSL	75
D	Port pin-outs	76
	Introduction	77
	Console port	77
	Ethernet 10Base-T and 100Base-T port	77
	Sync Serial Port	78
	V.35 Serial port	78
	X.21 Serial Port	79
	FXS port	79
	FXO port	79
	T1/E1 port	80
		6

Image 6

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables About this guide AudienceStructure Precautions Impaired functioningSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions SmartNode 4830 Getting Started GuideAbout this guide Chapter contents General informationSmartNode Model 4830 Series Overview SmartNode product SmartNode 4838 shownGeneral information SmartNode 4830 Series Detailed Description Examples of SN4830 Series rear panels FXS onlyModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Multiservice carrier access over leased lines IntroductionApplications for SmartNode 4830 Series Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Site log Network informationIP related information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default conﬁguration Conﬁgure IP addressConnect with the serial interface Login Changing the IP addressConnect the SmartNode to the network Load conﬁgurationBootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety complianceCompliance EMC complianceFCC Part 68 Acta Statement FXO ports Industry Canada Notice FXO portsCE Notice Authorized European RepresentativeAppendix B Speciﬁcations Sync serial interface if applicable Voice connectivityEthernet interface T1/E1 interface if applicableAdsl Daughter Card if applicable Shdsl Daughter Card if applicablePPP and Frame-Relay support Voice processing signaling dependentVoice signaling Fax and modem supportIP services Voice routing-session productManagement Power supply DimensionsWeight and power dissipation Operating environmentIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet straight-throughConnecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOT1/E1 DSLAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portSync Serial Port Serial portFXS port FXO portT1/E1 port ADSL/G.SHDSL portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number