Patton electronic SL4020 Typographical conventions used in this document, General observations

Page 18

SmartLink 4020 Getting Started Guide	About this guide

WARNING

WARNING

The SmartLink is not shipped with power cables. For AC powered units, ensure that the power cable used meets all applicable standards for the coun- try in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

Hazardous network voltages are present in WAN ports regardless of whether power to the SmartLink is ON or OFF. To avoid electric shock, use caution when near WAN ports. When detaching cables, detach the end away from the SmartLink ﬁrst.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

WARNING

Before opening the chassis, disconnect the telephone network cables to avoid contact with telephone line voltages. When detaching the cables, detach the end away from the SmartLink ﬁrst.

WARNING

Ultimate disposal of this equipment must be handled according to all applicable national laws and regulations.

CAUTION

General observations

•Clean the case with a soft slightly moist anti-static cloth

•Place the unit on a ﬂat surface and ensure free air circulation

•Avoid exposing the unit to direct sunlight and other heat sources

•Protect the unit from moisture, vapors, and corrosive liquids

Typographical conventions used in this document

This section describes the typographical conventions and terms used in this guide.

General conventions

The procedures described in this manual use the following text conventions:

		Table 1. General conventions

Convention		Meaning

Garamond blue type	Indicates a cross-reference hyperlink that points to a ﬁgure, graphic, table, or sec-
	tion heading. Clicking on the hyperlink jumps you to the reference. When you
	have ﬁnished reviewing the reference, click on the Go to Previous View
	button	in the Adobe® Acrobat® Reader toolbar to return to your starting point.

Garamond bold type	Indicates the names of command buttons that execute an action.

18

Image 18

Contents SL4020 Mailsupport@patton.com Summary Table of Contents Table of Contents Vlan Network-LAN Telephony Codecs System Table of Contents Documentation Calling Features List of Figures List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General observationsGeneral conventions SmartLink 4020 Getting Started GuideAbout this guide Chapter contents General informationSmartLink 4020 overview SmartLinkSmartLink installation Installing the router Do the followingConnect to the Internet service provider Connecting the SmartLink to the network Home System information System UptimeSystem information System Status Network-WAN Network-WAN Network Settings StatusInterface Status Settings Obtain WAN conﬁguration dynamically Device Operating ModeInternet Conﬁguration Specify ﬁxed WAN conﬁgurationSettings Enable PPPoEAuthentication WAN PPPoE ConﬁgurationMAC Spooﬁng Conﬁguration MTU SizeInternet Vlan Conﬁguration Saving your work QoS Quality of ServiceEnable Voice QoS Assured Bandwidth for VoiceToS/DiffServ TOS/DiffServ windowIPSec Conﬁguration Outbound ESP Authentication Algorithm Outbound AH Authentication AlgorithmOutbound AH Authentication Key HEX Outbound ESP Authentication Key HEXInbound ESP Authentication Key HEX Network-LAN Dhcp Static Address Assignment Server SettingsClient Network Information Viewing the Dchp Client TableStatic Routing RoutingDynamic Routing Viewing the Routing TablePort Forwarding to LAN Port ForwardingReserved Ports De-Militarized ZoneService Access IP FilteringFilter IP Range Ping Reply Telephony Telephony Line 2 Speed Dial Settings Speed Dial Serv VoIP Status VoIP Server Registration StatusPhone Line Status SIP Server Settings Gateway SettingsSIP Conﬁguration SIP Extensions RTP Telephone Event ConﬁgurationSIP Parameters SIP Timer Values secVoIP Vlan Conﬁguration Hook Flash Mime TypeNAT Traversal Audio/CODEC Conﬁguration PacketizationJitter Buffer Phone Number Phone 1 & PhoneUser Information User NameSupplementary Service Settings MWI Serv Call Transfer ServIP Dialing Serv Speed Dial ServCall Forward Settings Dial Out TypeHttp Digest Setting Selective Call Forward SettingsDistinctive Ring Settings Incoming Call BlockLine 1 Speed Dial Settings Speed DialSpeed Dial 1-8 Phone Number/IP Dialing Line 2 Speed Dial Settings System System System New User Password Set Security PasswordNew Root Password Conﬁrm new passwordConﬁguration LoggingManual Upgrade Auto UpgradeEnable Auto Upgrade Auto Upgrade URL Auto Upgrade ProtocolUpgrade Server LocalizationDistinctive Ring Setting Supplementary Service Keys DND Act Keys Dist Ring Act KeysWarm Line Act Keys IP Dialing Act KeysControl Timer Values Ring Setting MiscellaneousSnmp Conﬁguration FXS Port Polarity ConﬁgurationSnmp Trap Conﬁguration Snmp Community Conﬁguration Snmp System ConﬁgurationReload Documentation Introduction Documentation linkLogout Logout window Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Return for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix a Compliance information Compliance FCC Warning Radio and TV InterferenceCE-Mark Warning Appendix B Speciﬁcations Connectivity Voice Processing signalling dependentVoice Connectivity Fax and Modem SupportManagement Voice Services/FeaturesIP Services Operating EnvironmentAppendix C Dial plans Non-dialed Line Dial Plan Sample Dial PlansSimple Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Ring Cadence Conﬁguration Following is a sample ring cadence patter conﬁguration