Patton electronic 4960 Series manual SmartNode 4960 rear panel

Page 16

SmartNode 4960 Getting Started Guide	1 • General information

SmartNode 4960 rear panel

The SmartNode 4960 rear panel ports are described in table 4.

Power

(~120–240V, 50/60 Hz, 1A)

120-
240V,Power
50/60	Hz,	0/3
	Hz,	1A

0/2

	0/1
T1/E1	0/0

ETH

0/1

ETH

0/0

Reset	Console
	Console
	RS-
	232

SN4960/1E

Power 120-240V, 50/60 Hz, 1A

0/0	ETH 0/1	ETH 0/0	Console
			Reset
T1/E1			RS-232

Power 120-240V, 50/60 Hz, 1A

T1/E1

PRI port 0/0

						SN4960/4E
0/3	0/2	0/1	0/0	ETH 0/1	ETH 0/0		Console
						Reset
		T1/E1					RS-232
		T1/E1		ETH 0/1			Console
	PRI ports 0/3–0/0			ETH 0/1			Console
	PRI ports 0/3–0/0			10/100/1000Base-T port			RS-232 port
				10/100/1000Base-T port			RS-232 port
				ETH 0/0		RESET
				10/100/1000Base-T port		button

Figure 2. SN4960 rear panel

SmartNode 4960 overview

16

Image 16

Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral observations Typographical conventions used in this documentGeneral conventions Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings LoginConﬁguring the desired IP address Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the conﬁguration optional Bootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Conﬁguration Line Setup Conﬁguring PPPoEConﬁguration Summary Profile napt WANUsing PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Safety ComplianceRadio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Speciﬁcations Voice connectivity Voice processing signalling dependentData connectivity Fax and modem support Voice signallingVoice routing-session router IP services ManagementSystem PhysicalShdsl Daughter Card if applicable DSLIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl portAppendix E SmartNode 4960 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses