Patton electronic 4960 Series manual SmartNode 4960 overview

Page 14

SmartNode 4960 Getting Started Guide	1 • General information

SmartNode 4960 overview

The SmartNode 4960 T1/E1 PRI VoIP Router (see ﬁgure 1) combines IP routing, VPN/Security, and Quality of Service with high-quality Voice over IP (VoIP) delivered on 1 to 4 Primary Rate Interfaces (PRI T1/E1). This combination allows you to leverage low-cost Internet Telephony on existing ISDN Phones and PBX equipment for complete SoHo and branch ofﬁce voice and data connectivity.

Figure 1. SmartNode 4960

The SmartNode 4960 series consists of several models. They differ in the number of PRI ports and voice chan- nels supported. All models come equipped with two 10/100/1000Base-T Ethernet ports. The SmartNode 4960 PRI ports and voice channels are listed in table 2. The SmartNode 4960 G.SHDSL models are listed in table 3.

Table 2. SmartNode 4960 PRI Ports and Voice Channels

Model	PRI Ports	Voice Channels

SN4960/1E24V/UI	1	24

SN4960/1E30V/UI	1	30

SN4960/4E24V/UI	4	24

SN4960/4E30V/UI	4	30

SN4960/4E48V/UI	4	48

SN4960/4E60V/UI	4	60

SN4960/4E96V/UI	4	96

SN4960/4E120V/UI	4	120

SmartNode 4960 overview

14

Image 14

Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral observations Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConﬁguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the conﬁguration optional Start-up with factory conﬁguration BootloaderStart Bootloader Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Conﬁguration Line Setup Conﬁguring PPPoEConﬁguration Summary Profile napt WANUsing PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Speciﬁcations Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support System IP servicesManagement PhysicalShdsl Daughter Card if applicable DSLIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl portAppendix E SmartNode 4960 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses