Patton electronic 4960 Series manual Fax and modem support, Voice signalling

Page 51

SmartNode 4960 Getting Started Guide	B • Specifications

Fax and modem support

Automatic fax and modem detection

Codec fallback for modem-bypass

T.38 Fax-Relay (Gr. 3 Fax, 9.6 k, 14.4 k)

G.711 Fax-Bypass

Voice signalling

SIPv2

H.323v4

MGCP/IUA

SIP call transfer, redirect

Overlap or en-bloc dialing

DTMF in-band, out-of-band

Conﬁgurable progress tones

Voice routing—session router

Local switching (hairpinning)

Least cost routing

Interface huntgroups

Call-Distribution groups

Number blocking

Call Routing Criteria:

•Interface

•Calling/called party number

•Time of day, day of week, date

•ISDN bearer capability

•Various other information elements (IEs) of the ISDN setup

•Wildcard and regular expression matching

Regular expression number manipulation functions:

•Replace numbers

•Add/remove digits

•Pattern matching and replacement

Fax and modem support

51

Image 51

Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables About this guide AudienceStructure Safety when working with electricity PrecautionsTypographical conventions used in this document General observationsGeneral conventions Node General information Chapter contentsSmartNode SmartNode 4960 overviewSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel ports are described in table SmartNode 4960 rear panelWAN ETH 0/0 SN4960/4E SmartNode 4960 front panelLED Applications overview Application-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service Isdn Internet telephony IADApplications overview SmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Factory-default IP settingsLogin Conﬁguring the desired IP addressLAN Connecting the SmartNode to the networkLoading the conﬁguration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory conﬁgurationRedBoot ipaddress -g gateway Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Conﬁguration Conﬁguring PPPoE Line SetupProfile napt WAN Conﬁguration SummarySetting up permanent virtual circuits PVC Using PVC channels in bridged Ethernet modeUsing PVC channels with PPPoE Diagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information FCC Part 68 Acta Statement SafetyCompliance Radio and TV InterferenceCE Declaration of Conformity Industry Canada NoticeAppendix B Speciﬁcations Voice processing signalling dependent Voice connectivityData connectivity Voice signalling Fax and modem supportVoice routing-session router Physical IP servicesManagement SystemDSL Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identiﬁcation of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs EIA-561 RJ-45 8-pin port Console portShdsl port PRI portAppendix E SmartNode 4960 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination