Patton electronic 4960 Series manual Connecting the SmartNode to the network, Lan

Page 32

SmartNode 4960 Getting Started Guide

4 • Initial configuration

 

 

Now you can set your IP address and network mask for the interface ETH 0/0 (WAN). Within this example a network 172.16.1.0/24 address is assumed. The IP address in this example is set to 172.16.1.99 (you should set this the IP address given to you by your network provider).

192.168.1.1(ctx-ip)[router]#interface WAN 192.168.1.1(if-ip)[WAN]#ipaddress 172.16.1.99 255.255.255.0

2002-10-29T00:09:40

: LOGINFO

: Link

down on interface WAN.

2002-10-29T00:09:40

: LOGINFO

: Link

up on interface WAN.

172.16.1.99(if-ip)[WAN]#

 

 

Copy this modified configuration to your new start-up configuration. This will store your changes in non-vol- atile memory. Upon the next start-up the system will initialize itself using the modified configuration.

172.16.1.99(if-ip)[WAN]#copy running-config startup-config

172.16.1.99(if-ip)[WAN]#

The SmartNode can now be connected to your network.

3. Connecting the SmartNode to the network

In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the Smart- Node to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 4960 Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through or crossover cables for host or hub/ switch connections (see figure 8).

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, flammability, and

CAUTION mechanical serviceability.

120-

 

 

240V,Power

 

 

50/60

Hz,

0/3

 

1A

0/2

 

0/1

T1/E1

0/0

LAN

ETH 0/1

ETH 0/0

Console

RS-232

LAN (ETH 0/1)

WAN (ETH 0/0)

Network

 

Straight-through wired or crossover cable

 

 

Figure 8. Connecting the SmartNode to the network

3. Connecting the SmartNode to the network

32

Image 32
Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral observations Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings LoginConfiguring the desired IP address Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the configuration optional Bootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Profile napt WANUsing PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Safety ComplianceRadio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support IP services ManagementSystem PhysicalShdsl Daughter Card if applicable DSLIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl portAppendix E SmartNode 4960 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses