Patton electronic 4960 Series manual SmartNode 4960 front panel, SN4960/4E

Page 18

SmartNode 4960 Getting Started Guide	1 • General information

SmartNode 4960 front panel

Figure 3 shows SmartNode 4960 front panel LEDs, the LED deﬁnitions are listed in table 5.

Port0
T1/E1	Port1
	T1/E1	Port2
		T1/E1	Port3
			T1/E1

	SN4960/1E
Power
Activity	T1/E1 Port 0

VoIP			Ethernet 0/1
VoIP			Activity
Ethernet 0/0	Ethernet 0/0	Ethernet 0/1	Ethernet 0/1
Link	1000	Link	1000

Ethernet 0/0	Ethernet 0/0	Ethernet 0/1
100	Activity	100								SN4960/4E
										SN4960/4E
			Port	0	Port	1	Port	2	Port	3
		T1/E1	Port		Port		Port		Port
		T1/E1	T1/E1		T1/E1		T1/E1

T1/E1 Port 0	T1/E1 Port 3
T1/E1 Port 1	T1/E1 Port 2

Figure 3. SmartNode 4960 front panel

SmartNode 4960 overview

18

Image 18

Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General observationsGeneral conventions Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConﬁguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the conﬁguration optional Start-up with factory conﬁguration BootloaderStart Bootloader Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Conﬁguration Line Setup Conﬁguring PPPoEConﬁguration Summary Profile napt WANSetting up permanent virtual circuits PVC Using PVC channels in bridged Ethernet modeUsing PVC channels with PPPoE Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Speciﬁcations Voice processing signalling dependent Voice connectivityData connectivity Voice signalling Fax and modem supportVoice routing-session router System IP servicesManagement PhysicalShdsl Daughter Card if applicable DSLIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl portAppendix E SmartNode 4960 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses