Patton electronic 4960 Series manual IP services, Management, System, Physical

Page 52

SmartNode 4960 Getting Started Guide	B • Specifications

IP services

IPv4 router; RIPv1, v2 (RFC 1058 and 2453)

Programmable static routes

ICMP redirect (RFC 792); Packet fragmentation

DiffServe/ToS set or queue per header bits

Packet Policing discards excess trafﬁc

802.1p VLAN tagging IPSEC AH & ESP Modes Manual Key; IKE AES/DES/3DES Encryption

Management

Web-based GUI

Industry standard CLI with local console (RJ-45, RJ-231, 9600 bps, 8, N, 1) and remote Telnet access, fully documented

HTTP web management and ﬁrmware loading

TFTP conﬁguration & ﬁrmware loading

SNMP v1 agent (MIB II and private MIB)

Built-in diagnostic tools (trace, debug)

Secure Auto-provisioning

System

CPU Motorola MPC8360 series operating at 266/400 MHz

Memory:

•128 Mbytes RAM (DDR, 266MHz)

•8 Mbytes Flash

Physical

Dimensions: 11.9W x 1.71H x 7.16D inch (302W x 44H x 182mm)

Weight: <21 oz. (<600g)

Power Consumption: < 16W

Operating temperature: 32–104°F(0–40°C)

Operating humidity: up to 90%, non condensing

IP services

52

Image 52

Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral observations Typographical conventions used in this documentGeneral conventions Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings LoginConﬁguring the desired IP address Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the conﬁguration optional Bootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Conﬁguration Line Setup Conﬁguring PPPoEConﬁguration Summary Profile napt WANUsing PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Safety ComplianceRadio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Speciﬁcations Voice connectivity Voice processing signalling dependentData connectivity Fax and modem support Voice signallingVoice routing-session router IP services ManagementSystem PhysicalShdsl Daughter Card if applicable DSLIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl portAppendix E SmartNode 4960 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses