Patton electronic 4960 Series manual Termination, Other licenses

Page 67

SmartNode 4960 Getting Started Guide

F • End user license agreement

 

 

If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Gov- ernment agrees that such Program(s) are commercial computer software or computer software documentation and that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS 227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.

6. Termination

A)The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s).

B)Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License” on page 66.

C)Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of the licensed Program(s)

7. Other licenses

The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identi- fied to the Programs includes:

A routing license is included at no charge.

MGCP capabilities will require the purchase of an additional license.

The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL license terms (http://www.gnu.org/licenses/lgpl.html).

RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/license- overview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html). Source code is available upon request.

End User License Agreement

67

Image 67
Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsGeneral observations Typographical conventions used in this documentGeneral conventions Node General information Chapter contentsSmartNode SmartNode 4960 overviewSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel ports are described in table SmartNode 4960 rear panelWAN ETH 0/0 SN4960/4E SmartNode 4960 front panelLED Applications overview Application-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service Isdn Internet telephony IADApplications overview SmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Factory-default IP settingsLogin Configuring the desired IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory configurationRedBoot ipaddress -g gateway Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupProfile napt WAN Configuration SummaryUsing PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Diagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information FCC Part 68 Acta Statement SafetyCompliance Radio and TV InterferenceCE Declaration of Conformity Industry Canada NoticeAppendix B Specifications Voice connectivity Voice processing signalling dependentData connectivity Fax and modem support Voice signallingVoice routing-session router Physical IP servicesManagement SystemDSL Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs EIA-561 RJ-45 8-pin port Console portShdsl port PRI portAppendix E SmartNode 4960 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination