ZyXEL Communications IES1248 manual Setup ES4024 Enable Spanning Tree protocol on Ethernet ports

Page 35

IES 1248 Support Notes

3. Setup ES4024

3.1 Enable Spanning Tree protocol on Ethernet ports

Click Advanced Application, Spanning Tree Protocol in the navigation panel to

display configuration screen as shown. You will see the Spanning Tree Protocol

Status page. Click Configuration to configure panning tree protocol settings.

Click Active to enable Spanning Tree Protocol. Then enable it on Port 1 and Port 2.

35

All contents copyright (c) 2006 ZyXEL Communications Corporation.

Image 35

Contents IES1248 IES 1248 Support Notes Trouble Shooting Internet IES-1248 How to apply the profile to portsIES-1248 Settings Provide Different DSL Port Speeds to different subscribersIES 1248 Support Notes Profile Assignment IES 1248 Support Notes Prestige 660R-61 Settings Check the values above are the same as the IES-1248 How to configure 802.1Q Vlan Adsl Adsl How to set up a Vlan environmentIES 1248 Support Notes Pvid settings Triple play Application Internet How to set up a Multiple PVCs environmentVC profile setup Multiple PVCs setup Prestige 660R-61 Settings ES-2024 settings IES 1248 Support Notes Pvid setup IES 1248 Support Notes Application server Authentication Server RadiusHow to set up an 802.1x environment 802.1x ApplicationRadius settings IES-1248 Authenticator settingsRadius server setup Vantage 50RADIUS settings802.1x/MD5-challenge setup Windows XPSupplicant settingsIES 1248 Support Notes Network IES-1248 Setting up the Syslog ServerHow to set up a Syslog server Install and Run Kiwi’s Syslog ServerIES-1248 settings Setting up the Ring Environment Adsl How to set up a Ring EnvironmentENET2 port Setup IES2000 Enable Spanning Tree protocol Click Uplink2 to set up this port Check Spanning Tree Protocol to enable it Setup ES4024 Enable Spanning Tree protocol on Ethernet ports Results Port Setting up the Igmp Snooping/IGMP FilteringInternet Server Ethernet PortIES-1248 settings Enable Igmp Snooping How to set up Igmp snooping/IGMP filteringSet up Igmp Filtering Static Multicast What is Static Multicast Filter?Application Scenario How to configure Static Multicast filter IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes Limit the users behind the certain DSL port IES-1248 settings 1.1 Set up MAC filter PC 1 PC How to set up MAC Filter/Port SecuritySet up Port Security Dhcp Relay Option 82 Application Server Dhcp Client How to set up Dhcp Relay Option 82 EnvironmentNetwork IP Commander settings CPE settingsIES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes Rule creation has been finished Network Client Client How to Filter Some Specific PacketFilter Some Certain Packet IES 1248 Support Notes Internet Cascade two IES1248 Daisy chain modeHow to setup Daisy-chain mode Vlan Application How to configure Vlan IES 1248 Support Notes Port 23, fixed, Tx tagging Port 2, port For Switch B on Floor Please set static Vlan 10 port 23, fixed, untag IES 1248 Support Notes Application Scenario C Port 23, fixed, Tx tagging Port 2, port For Switch B on Floor IES 1248 Support Notes Vlan ID IES 1248 Support Notes IES 1248 Support Notes IES 1248 Support Notes What is the Adsl chipset of IES1248? What is the maximum line rate of IES1248 ?What is the difference between IES1248-71 and IES1248-73 ? What is the power requirement of IES- 1248?How many VLANs can each Adsl port of IES1248 join ? What kind of the features that IES 1248 supports ?What is the default console rate of IES1248 ? How many static Vlan entries can IES1248 support ?IES 1248 Support Notes Trouble Shooting IES 1248 Support Notes WEB How to reset this device as factory default?IES 1248 Support Notes Cccc Å Send file to MSC via 1K-Xmodem when see this message MSC 1000 atlc Starting Xmodem upload CRC modeWEB IES 1248 Support Notes XDSL link fail? Which new version I should upgrade?Can not access the Dslam via console port. What should I do? Forgot the Password, how do I recover it?Alarm Led is always on, what should I do?