Agilent Technologies DP106, DP240, DP212, DP214, DP110, DP1400 After Restarting Windows, Windows XP

Page 24

3.Turn on the power of the crate(s), if present, and then the PC and start the operating system.

NOTE: Acqiris Digitizers are equipped with a LED. If this LED is not glowing orange or red when the power is applied there is a severe problem. Either the module is broken or the necessary voltages for its use are not available.

NOTE: For proper system operation when using the IC200, IC414, or other PCI extension interface to connect a CC10X crate to a remote PC, the crate must be powered on before the PC in order for the PC BIOS to recognize the presence of the CompactPCI crate.

4.Devices that were installed using a previous version of Acqiris Software the instruments in these logical positions will still appear as Unknown Devices. This can be changed to the new Acqiris type category with the Grey Diamond icon by Uninstalling the device and then Installing again. Instructions on this procedure can be found in the ReadMe.txt file in the manuals folder of your Acqiris Software installation.

2.5. After Restarting

2.5.1. Windows 2000

Under Windows 2000, you must login with administrator privileges after the first boot following the hardware installation; the Plug&Play system must have the appropriate privileges to be able to complete your hardware installation successfully. After a successful hardware installation, you will be able to use your Acqiris Digitizer(s) with normal privileges.

At the first boot following the hardware installation, Windows will detect the new hardware and will install the devices automatically. The following image will appear.

NOTE: In some systems an application program (such as AcqirisLive) will not yet work correctly at this point. One additional boot cycle may be needed if this is the first time that a hardware board is being installed.

2.5.2. Windows XP

Under Windows XP, you must login with administrator privileges after the first boot following the hardware installation; the Plug&Play system must have the appropriate privileges to be able to complete your hardware installation successfully. After a successful hardware installation, you will be able to use your Acqiris Digitizer(s) with normal privileges.

If you login with administrator privileges after the first boot following the hardware installation, Windows will detect the new hardware and start the “Found New Hardware Wizard” after a few seconds.

User Manual: Family of 8-bit Digitizers

Page 24 of 66

Image 24
Contents Agilent Acqiris Family BIT Digitizers XZ001USA Contents OUT of the BOX Running the Acqirislive Application Using this Manual Message to the UserConventions Used in This Manual Disclaimer and Safety Packaging and HandlingWarranty System RequirementsMaintenance Transport & ShippingCleaning Disposal and RecyclingIC414 Installation 1. IC414 Hardware installation hints 2. IC414 Windows software installationInstalling the Software under Windows InstallationMultiple Versions Page Page Page Page Page Page Page Page Page Installing the Software for Linux Kernel Mode Driver Compilation ƒ cd linuxdriverpciInstalling the Hardware Special casesEnvironment variables for the Firmware After Restarting Windows Windows XPPage LabVIEW RT Installing the IVI-COM/C Driver Distribution for Windows 2000/XP and LinuxDP110 Block Diagram OverviewChannel Input Coupling ImpedanceInput Protection Mezzanine Front-endOffset Particularities Vertical Resolution Input Voltage and OffsetDC Accuracy and Linearity Using Probes Data AcquisitionSampling Rate Acquisition MemorySingle and Sequence Acquisition Modes Timing Timebase RangeCombining channels TriggerTrigger Coupling Trigger LevelEdge Trigger Slope Window TriggerPre- and Post-Trigger Delay Trigger StatusExternal Clock and Reference Internal Calibration ASBusSpecial Front Panel Input and OutputDP1400 & DC271-FAMILY Frequency Counter mode External Trigger Output DP1400 & DC271-FAMILYPCI DMA Operating Temperature DimensionsSafety Environmental and PhysicalRunning the AcqirisLive Application Getting Started with AcqirisLiveControl Panel Mode Control Panel and FunctionsDisplaying Multiple Traces Numeric Editor Keyboard shortcutsInput Voltage Scale, Offset and Coupling Acquisition Mode Using digitizers of different models simultaneously Timebase and MemoryDisplay Features, Zoom and Persistence Segmented MemorySetup Top Line Menu of AcqirisLiveStore, Autostore and Conversion of Waveforms Page Calibrate Combine channelsExternal 10 MHz Reference and External Clock Additional Waveform InformationDisplay Features Command Line SwitchesAvailable Switches Operation ModeTransient Recorder mode Buffer sizeBanks for Smar CalibrationSimulation Mode Temperature UpdateAcquisition State Multi-instrumentsWhen should the GeoMapper Application be used How to run GeoMapperWho needs a Geographical Map of Modules Page Page Page Appendix B ASBus2 for PCI Digitizers Page Page Page Page Page Appendix H XP104 Fan Unit for DP1400 Page Appendix I XP105 Fan Unit for DP1400