Canon LV-X2 owner manual Appendix, Lamp Replacement

Page 37

APPENDIX

LAMP REPLACEMENT

LAMP REPLACE

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

This indicator lights yellow when the life of the projection lamp draws to an end. Replace the Projection Lamp with a new one promptly.

TOP CONTROL

READY

LAMP

REPLACE

RNING LAMP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Allow the projector to cool, for at least 45 minutes before

For continued safety, replace with a lamp assembly of

 

 

you open the Lamp Cover. The inside of a projector can

 

the same type.

 

 

become very hot.

 

Do not drop the lamp assembly or touch the glass bulb!

 

 

 

 

 

The glass can shatter and may cause injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect the AC plug. Allow the

projector to cool at least for 45 minutes.

2

To remove the Lamp Cover, remove the screw with a

screwdriver .

3

Remove the 2 screws with a screwdriver and pull out Lamp

Assembly by grasping Handle.

4

Replace the Lamp Assembly with a new one and tighten 2

screws back into position. Make sure that the Lamp Assembly is

 

set properly. Replace Lamp Cover and tighten the screw.

5

projector.Connect the AC Power Cord to the projector and turn on the

6

Reset the Lamp Replace Counter.

Refer to “LAMP REPLACE COUNTER” on the next page .

NOTE : Do not reset the Lamp Replace Counter when Projection Lamp is not replaced.

SCREW

LAMP COVER

HANDLE

LAMP

ASSEMBLY

SCREW

ORDER REPLACEMENT LAMP

The Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.

Model No. of your projector

:

LV-X2

Replacement Lamp Type No.

:

LV-LP15

 

 

 

(Service Parts No. 610 300 7267)

37

Image 37
Contents LV-X2 To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Wide Zoom Lens Features and DesignNomenchtor PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP the ProjectorFor Continental Europe Preparation Positioning the Projector Adjustable FeetRoom Light Moving the Projector Preparation Mounting the Lens CoverTerminals of the Projector Connecting the ProjectorVideo AV AudioTerminals Projector Connecting to a ComputerAudio OUT Connecting Video EquipmentBefore Operation Operation of the Remote Control UnitBattery Remote Control Unit Battery InstallationBefore Operation Operating Range Ready Indicator TOP Controls and IndicatorsOperating the ON-SCREEN Menu HOW to Operate the ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARTurning on / OFF the Projector Basic OperationTurning on the Projector Turning OFF the ProjectorZoom Adjustment Adjusting the ScreenFocus Adjustment Keystone AdjustmentTimer Function Sound AdjustmentBasic Operation No Show Function Direct OperationSelecting the Input Source Computer InputSelecting the Computer System AutoResolution Computer Input Compatible Computer SpecificationsFreq KHzAuto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Video InputAuto Selecting the Video SystemAV System Menu Video or S-VIDEO AV System Menu Component VideoCinema Video Input Image Level Adjustment Reset all adjustment to the previous figure Setting Menu SettingSetting Menu Power management To change the code of the Remote Control UnitRemote control Lamp counter resetAppendix Lamp ReplacementLamp Replace Appendix Lamp Replace Counter Lamp Handling PrecautionsAIR Filter Care and Cleaning MaintenanceCleaning Projection Lens RecommendationTroubleshooting Does not work Remote Control UnitOptional Parts Technical SpecificationsControl Port Connector Appendix Configurations of the TerminalsUSB Connector Series B Computer Input Terminal AnalogCanon U.S.A., INC