Canon 7585 manual Usb

Page 52

Setting

USB

The Projector has a USB port for interactive operation between the projector and computers. Set the mode by following the steps below.

Wireless Mouse mode

Select “” when controlling a computer with the remote control unit of this projector.

Projector mode:

” Not used.

Power management

For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period.

If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with “No signal” appears. It starts the countdown until the lamp is turned off. The countdown time can be set between 1 and 30 minutes.

Use the Point  buttons to set the countdown timer.

Select one of the following options:

Ready . . . . When the lamp has been fully cooled down, the POWER indicator starts blinking. In this condition, the projection lamp is turned on if the input signal is reconnected or any button on the side control or remote control unit is pressed .

Shutdown . . When the lamp has been fully cooled down, the power is turned off.

Off . . . . . . . Power Management function is off.

Note:

• Factory default is “Ready: 5 min.”

On start

When this function is set to “On,” the projector will be automatically turned on just by connecting the AC power cord to the wall outlet.

Note:

Be sure to turn off the projector properly (see “Turning Off the Projector” on page 24). If the projector is turned off in the incorrect sequence, the On start function does not work properly.

Pointer

You can emphasize a part of the projected image with this function. Use the Point  buttons to select a pattern of the Pointer (Arrow, Cross, or Dot) (P. 30)

Note:

The Point !  buttons and OK button are invalid when the Pointer function is operating.

Power management

Time left before the lamp is off

Press the OK button at Power management and the dialog box appears. Use the Point  buttons to choose one of the three options.

Press the Point button to select the timer, and then use the Point 

buttons to set the timer

52

Image 52
Contents 8VHU·V0DQXDO Features and Design Table of Contents To The Owner Risk of Electric Shock Do not OpenSafety Instructions Air Circulation Top PanelInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorAC Power Cord for the United States and Canada ComplianceFederal Communications Commission Notice Canadian Radio Interference RegulationsPart Names and Functions Front BackBottom  Top Cover Release Button Lens CapUSB Connector Series B Reset buttonRear Terminal INFRARED Remote Receiver BackSide Control and Indicators Indicators on the top panelRemote Control Unit P-TIMER button FOCUS buttons Adjust the focus p.28 BLANK buttonMENU button D-ZOOM buttonRemote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Transmitter Remote Control Code Adjustable Feet InstallationPositioning the Projector Lens Installation Removing the lensAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB DVI-Digital Cable = USB Cable BNC Cable =Connecting to Video Equipment Video, S-Video Monitor Out Signal TableFor the U.K Connecting the AC Power CordFor the U.S.A. and Canada For Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote Control UnitSide Control On-Screen MenuMenu Bar Zoom Adjustment Focus AdjustmentLens Shift Adjustment Operating with Projector ControlOperating with Remote Control Unit Timer button Filter buttonBlank button Mouse Pointer buttonPointer Function Wireless Mouse OperationPointer Remote Control Operation Remote Control button operationInput Selection InputComputer Input Source Selection Menu OperationInput Menu Source Select MenuWhen Selecting Input 3 AV Terminals Video Input Source SelectionComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment PC Adjust MenuDirect Operation Auto PC adjManual PC Adjustment Reset Mode free To clear the adjusted dataTo store the adjusted data StoreImage Level Selection StandardHigh contrast CustomScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksCinema Provide the image at the normal video aspect ratio Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuList Color M Menu Color PaletteWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLogo select LogoLogo Capture Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code RC sensor USB PIN code lock Security Key lockSecurity Change the PIN Code Lock setting Change the PIN CodeFilter counter Factory defaultTest pattern Maintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.58 Replacing the Filter CartridgeResetting the Filter Counter Resetting the Scroll CounterFilter counter Scroll counterLamp Replacement Lamp Replace indicatorReset the Lamp counter p.60 Top PanelResetting the Lamp Counter Order Replacement LampLamp Handling Precautions Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other four indicators blink Then check the matters belowTroubleshooting AppendixRemote control unit Wireless mouseDoes not work Function does notImage Adjust Menu TreeComputer Input/Video Input InformationPC Adjust SystemImage Select ScreenSetting USBProjector is operating normally Indicators and Projector ConditionProjector is detecting abnormal condition Appendix Indicators Compatible Computer Specifications Resolution59.940 Panel Resolution Signal CompatibilityPower AccessoriesLens Replacement To the sales and service engineersOptional Parts PJ Link NoticeConfigurations of Terminals USB Connector Series BControl Port Connector D-sub 9 pin ANALOG/ Monitor OUT Mini D-sub 15 pinWhile the projector is locked with the PIN code Dimensions Operation Serial Control InterfaceExample Functional Execution Command FormatStatus Read Command CR0Canon Deutschland GmbH Canon Italia S.p.ACanon Schweiz A.G Canon GmbH