Canon 7585 manual Installing the Projector in Proper Directions, Positioning Precautions

Page 7

Safety Instructions

Installing the Projector in Proper Directions

Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard.

This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the horizontal plane. When installing the projector in downwardly inclined position, install the projector bottom side up.

Note:

• When the image is top/bottom and left/right reversed, set the ceiling function to “On.” (pp. 40, 44)

Positioning Precautions

Avoid positioning the projector as described below when installing.

10˚

10˚

Do not tilt the projector more than

 

 

10 degrees from side to side.

 

 

 

 

 

10˚

 

Do not put the projector on either side to project an image.

10˚

In upward projection, do not tilt the projector over 10 degrees right and left.

In downward projection, do not tilt the projector over 10 degrees right and left.

10˚

10˚

CAUTION ON CEILING MOUNTING

For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty on this projector does not cover any damage caused by use of any non- recommened ceiling mount kit or installation of the ceiling mount kit in an improper location.

7

Image 7
Contents 8VHU·V0DQXDO Features and Design Table of Contents Risk of Electric Shock Do not Open To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorCanadian Radio Interference Regulations AC Power Cord for the United States and CanadaCompliance Federal Communications Commission NoticeTop Cover Release Button Lens Cap Part Names and FunctionsFront Back Bottom INFRARED Remote Receiver Back USB Connector Series BReset button Rear TerminalIndicators on the top panel Side Control and IndicatorsRemote Control Unit D-ZOOM button P-TIMER buttonFOCUS buttons Adjust the focus p.28 BLANK button MENU buttonRemote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Transmitter Remote Control Code Adjustable Feet InstallationPositioning the Projector Removing the lens Lens InstallationAttaching the lens to the projector DVI-Digital Cable = USB Cable BNC Cable = Connecting to a Computer Digital and Analog RGBMonitor Out Signal Table Connecting to Video Equipment Video, S-VideoFor the U.K Connecting the AC Power CordFor the U.S.A. and Canada For Continental Europe Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Unit Side ControlMenu Bar Operating with Projector Control Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentOperating with Remote Control Unit Mouse Pointer button Timer buttonFilter button Blank buttonPointer Function Wireless Mouse OperationPointer Input Remote Control OperationRemote Control button operation Input SelectionSource Select Menu Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection When Selecting Input 3 AV TerminalsSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemAuto PC adj Auto PC AdjustmentPC Adjust Menu Direct OperationManual PC Adjustment Store ResetMode free To clear the adjusted data To store the adjusted dataCustom Image Level SelectionStandard High contrastScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackCinema Provide the image at the normal video aspect ratio Keystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeColor Palette Color MMenu List Color M MenuGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLogo select LogoLogo Capture Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code RC sensor USB PIN code lock Security Key lockSecurity Change the PIN Code Change the PIN Code Lock settingFilter counter Factory defaultTest pattern Filter Instructions Maintenance and CareReplacing the Filter Cartridge Reset the filter counter and the scroll counter p.58Scroll counter Resetting the Filter CounterResetting the Scroll Counter Filter counterTop Panel Lamp ReplacementLamp Replace indicator Reset the Lamp counter p.60Order Replacement Lamp Resetting the Lamp CounterLamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other four indicators blinkAppendix TroubleshootingFunction does not Remote control unitWireless mouse Does not workInformation Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectUSB SettingProjector is operating normally Indicators and Projector ConditionProjector is detecting abnormal condition Appendix Indicators Resolution Compatible Computer Specifications59.940 Accessories Panel ResolutionSignal Compatibility PowerPJ Link Notice Lens ReplacementTo the sales and service engineers Optional PartsANALOG/ Monitor OUT Mini D-sub 15 pin Configurations of TerminalsUSB Connector Series B Control Port Connector D-sub 9 pinWhile the projector is locked with the PIN code Dimensions Operation Serial Control InterfaceExample Format Functional Execution CommandCR0 Status Read CommandCanon GmbH Canon Deutschland GmbHCanon Italia S.p.A Canon Schweiz A.G