Canon 7585 manual Lamp Replacement, Top Panel, Lamp Replace indicator, Reset the Lamp counter p.60

Page 59

Maintenance and Care

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.

Filter cover

Top Panel

Lamp cover

Lamp replacement icon

Screw

LAMP REPLACE indicator

Note:

•The Lamp replacement icon will not appear when the Display function is set to “Off” (p.48), during “Freeze” (p.28), or “Blank” (p.29).

Follow these steps to replace the lamp.

1Turn off the projector and unplug the AC power cord. Let the projector cool for at least 45 minutes.

2Open the filter cover. (p.57)

3	Loosen the screw and open the lamp cover. Pull out the
	lamp by using the built in handle.

Handle

Lamp

4Replace the lamp with a new one. Make sure that the lamp is properly and fully inserted.

5

6

7

8

Close the lamp cover and secure the screw.

Close the filter cover.

Connect the AC power cord to the projector and turn on the projector.

Reset the Lamp counter (p.60)

Note:

•Be sure to insert the lamp in the correct direction.

•Do not reset the Lamp counter when the projection lamp is not replaced.

CAUTION

Allow a projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop the lamp or touch the glass bulb! The glass can shatter and may cause injury.

59

Image 59

Contents 8VHU·V0DQXDO Features and Design Table of Contents Risk of Electric Shock Do not Open To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorCanadian Radio Interference Regulations AC Power Cord for the United States and CanadaCompliance Federal Communications Commission NoticeTop Cover Release Button Lens Cap Part Names and FunctionsFront Back Bottom INFRARED Remote Receiver Back USB Connector Series BReset button Rear TerminalIndicators on the top panel Side Control and IndicatorsRemote Control Unit D-ZOOM button P-TIMER buttonFOCUS buttons Adjust the focus p.28 BLANK button MENU buttonWired Remote Control Transmitter Remote Control Battery InstallationRemote Control Receivers and Operating Range Remote Control Code Positioning the Projector InstallationAdjustable Feet Removing the lens Lens InstallationAttaching the lens to the projector DVI-Digital Cable = USB Cable BNC Cable = Connecting to a Computer Digital and Analog RGBMonitor Out Signal Table Connecting to Video Equipment Video, S-VideoFor the U.S.A. and Canada For Continental Europe Connecting the AC Power CordFor the U.K Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Unit Side ControlMenu Bar Operating with Projector Control Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentOperating with Remote Control Unit Mouse Pointer button Timer buttonFilter button Blank buttonPointer Wireless Mouse OperationPointer Function Input Remote Control OperationRemote Control button operation Input SelectionSource Select Menu Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection When Selecting Input 3 AV TerminalsSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemAuto PC adj Auto PC AdjustmentPC Adjust Menu Direct OperationManual PC Adjustment Store ResetMode free To clear the adjusted data To store the adjusted dataCustom Image Level SelectionStandard High contrastScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackCinema Provide the image at the normal video aspect ratio Keystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeColor Palette Color MMenu List Color M MenuGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLogo Capture LogoLogo select Change the Logo PIN code Change the Logo PIN code lock settingEnter a Logo PIN code RC sensor USB Security Security Key lockPIN code lock Change the PIN Code Change the PIN Code Lock settingTest pattern Factory defaultFilter counter Filter Instructions Maintenance and CareReplacing the Filter Cartridge Reset the filter counter and the scroll counter p.58Scroll counter Resetting the Filter CounterResetting the Scroll Counter Filter counterTop Panel Lamp ReplacementLamp Replace indicator Reset the Lamp counter p.60Order Replacement Lamp Resetting the Lamp CounterLamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other four indicators blinkAppendix TroubleshootingFunction does not Remote control unitWireless mouse Does not workInformation Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectUSB SettingProjector is detecting abnormal condition Indicators and Projector ConditionProjector is operating normally Appendix Indicators Resolution Compatible Computer Specifications59.940 Accessories Panel ResolutionSignal Compatibility PowerPJ Link Notice Lens ReplacementTo the sales and service engineers Optional PartsANALOG/ Monitor OUT Mini D-sub 15 pin Configurations of TerminalsUSB Connector Series B Control Port Connector D-sub 9 pinWhile the projector is locked with the PIN code Dimensions Example Serial Control InterfaceOperation Format Functional Execution CommandCR0 Status Read CommandCanon GmbH Canon Deutschland GmbHCanon Italia S.p.A Canon Schweiz A.G