BOXLIGHT MP-57i, MP-58i user manual Lamp

Page 38

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

If the lamp should break (it will make a loud bang when it does), ventilate

Disconnect the the room well, and make sure not to breathe the gas that comes out of plug from the the projector vents, or get it in your eyes or mouth.

power outlet

Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Use only the lamp of the specified type DT00601.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

37

Image 38
Contents MP-57i / MP-58i Trademark Acknowledgment Projector Features PreparationContents Projector Front/Right Part NamesProjector Audio in 1 port E Audio in 2 portControl Buttons Remote ControlRemote Control Setting Up ArrangementAdjusting The Projectors Elevator Using The Lens Shift ButtonsConnecting Your Devices ComputerProjector If using a M1-D input to mouse controlIf using a BNC input NetworkIf using a Scart RGB input If using a s-video signalIf using a component signal VCR/DVD Player ProjectorMonitorProjector Connecting The Power SupplySafety Guide and the following SpeakerProjectorAbout The Laser Pointer Remote ControlPeople. The laser beam can cause vision problems Putting BatteriesOperating The Remote Control Using The Remote ID FeatureUsing The Mouse/Keyboard Control Function Turning Off The Power Power ON/OFFTurning On The Power Selecting An Input Signal OperatingAt a RGB signal not M1-D At a video signal Using The Automatic Adjustment FeatureAt a M1-D signal At a RGB signalPosition Use the cursor buttons Adjusting The Picture PositionCorrecting The Keystone Distortion Dialog and complete this operationTemporarily Blanking The Screen Adjusting The VolumeMuting The Sound Press the Magnify Button Using The Magunify FeatureFreezing The Screen Displaying The Child Window Selecting An Audio InputEx. Turning off the built-in speaker Multifunctional SettingsUsing The Menu Functions Main Menu PICTURE-1 Menu SAVE1 SAVE2 SAVE3 SAVE4 PICTURE-1 MenuLOAD1 LOAD2 LOAD3 LOAD4 Size PICTURE-2 MenuPosition Component Input MenuColor Space 3D-YCSInput Menu Power on AdjustPower OFF Auto MenuSearch Auto MenuRGB BNC Video ComponentStart UP Screen MenuBlank Menu PositionMessage How to register your picture as the MyScreenScreen Menu Option Menu Option Menu Dhcp SetupNetwork Menu OFFEx. Case of IP Address = Network Setting UpClick Return to top Click Reboot to complete this operation Lamp Knob Replacing The LampDealer to replace the lamp Air Filter Caring For The Air FilterCaring For The Inside Of The Projector Caring For The Cabinet And Remote ControlOther Care Caring For The LensTroubleshooting Related MessagesRelated Messages Regarding The Indicator Lamps Regarding The Indicator Lamps Such as by a power outage blackout, etc Phenomena That May Easily Be Mistaken For Machine DefectsPhenomena That May Easily Be Mistaken For Machine Defects Sound is mutedWarranty And After-Service Specifications