BenQ MS504 Connecting video source devices, Connecting audio, Terminal name Terminal appearance

Page 16

If you wish to use this connection method when the projector is in standby mode, make sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings" on page 43 for details.

Connecting video source devices

You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Terminal name

Terminal appearance

Picture quality

Component Video

 

Better

S-Video

 

Good

Video

 

Normal

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted (except for the Power On/Off Ring Tone) when the AUDIO OUT jack is connected.

The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 16 for details.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

16 Connection

Image 16
Contents MS504/MX505 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorTeaching Coordinate Chart Template Whiteboard Menu operationMenu system Main menu Sub-menu OptionsBasic Ceiling/Front CeilingMenu Display Sec/10 sec/20 sec/30 sec Time AlwaysAdvanced Description of each menu Apply 3D Settings Save 3D SettingsTeaching Template Description 3D Sync InvertFunction Description Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorSystem Setup Basic menu Function Description Presentation TimerInstallation SettingsLock BackgroundColor Splash ScreenSystem Setup Advanced menu Function Description Reset AllClosed CaptionSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Warranty and Copyright information Limited warrantyCopyright Disclaimer