BenQ MX505, MS504 user manual Advanced

Page 37

Main menu	Sub-menu		Options

	High Altitude Mode		On/Off
		Mute	On/Off
	Audio Settings	Volume
	Audio Settings	Power On/Off	On/Off
		Power On/Off
		Ring Tone
		Ring Tone
		Lamp Mode	Normal/Economic/SmartEco/
		Lamp Mode	LampSave
	Lamp Settings		LampSave
	Lamp Settings	Reset Lamp Timer
		Reset Lamp Timer
5.		Equivalent Lamp
5.	Security	Change Password
SYSTEM
		Change Security
	Settings	Change Security	Power On Lock
SETUP:		Settings
Advanced	Baud Rate		2400/4800/9600/14400/19200/
	Baud Rate		38400/57600/115200
			38400/57600/115200
	Test Pattern		On/Off
		Closed Caption	On/Off
	Closed Caption	Enable	On/Off
	Closed Caption	Enable
		Caption Version	CC1/CC2/CC3/CC4
	Standby	Monitor Out	On/Off
	Standby	Audio Pass
	Settings	Audio Pass	Off/Audio in
	Settings	Through	Off/Audio in
		Through
	Reset All Settings
			•	Source
			•	Picture Mode
6.			•	Lamp Mode
INFORMA	Current System Status		•	Resolution
INFORMA	Current System Status		•	3D Format
TION			•	3D Format
TION			•	Color System
			•	Equivalent Lamp
			•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 37

Image 37

Contents MS504/MX505 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu operation Teaching Coordinate Chart Template WhiteboardMenu system Main menu Sub-menu OptionsCeiling/Front Ceiling BasicMenu Display Sec/10 sec/20 sec/30 sec Time AlwaysAdvanced Description of each menu Save 3D Settings Apply 3D SettingsTeaching Template Description 3D Sync InvertTemperature Function Description Picture ModeColor Temperature Fine Tuning 3D ColorTimer System Setup Basic menu Function Description PresentationInstallation SettingsBackground LockColor Splash ScreenReset All System Setup Advanced menu Function DescriptionClosed CaptionSystem CurrentStatus Care of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer

Main menu

SETUP:

Advanced

CC1/CC2/CC3/CC4