BenQ MS504, MX505 user manual Shutting down the projector, Direct power off

Page 34

Shutting down the projector

1.Press POWER and a confirmation message will display prompting you. If you don't respond in a few seconds, the message will disappear.

2.Press POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 41 for details.

3.Once the cooling process finishes, a "Power Off

Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop. Disconnect the power cord from the power outlet.

• To turn off the power ring tone, see "Turning off the Power On/ Off Ring Tone" on page 32 for details.

•If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a

few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

•Lamp life results will vary depending on environmental conditions and usage.

Direct power off

The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

34 Operation

Image 34

Contents MS504/MX505 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Teaching Coordinate Chart Template WhiteboardMenu operation Main menu Sub-menu OptionsMenu Display Sec/10 sec/20 sec/30 sec BasicCeiling/Front Ceiling Time AlwaysAdvanced Description of each menu Teaching Template Description Apply 3D SettingsSave 3D Settings 3D Sync InvertColor Temperature Function Description Picture ModeTemperature Fine Tuning 3D ColorInstallation System Setup Basic menu Function Description PresentationTimer SettingsColor Splash LockBackground ScreenClosed System Setup Advanced menu Function DescriptionReset All CaptionSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer