BenQ MS504, MX505 user manual Setting a preferred color temperature, 3D Color Management

Page 28

Setting a preferred color temperature

To set a preferred color temperature:

1.Highlight Color Temperature and select Warm, Normal or Cool by pressing

/ on the projector or remote control.

2.Press to highlight Color Temperature Fine Tuning and press MODE/ ENTER. The Color Temperature Fine Tuning page appears.

3.Press / to highlight the item you want to change and adjust the values by pressing / .

R Gain/G Gain/B Gain: Adjusts the contrast levels of Red, Green, and Blue.

R Offset/G Offset/B Offset: Adjusts the brightness levels of Red, Green, and Blue.

4.Press MENU/EXIT to exit and save the settings

3D Color Management

In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room.

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.

Proper color management can only be achieved under controlled and reproducible viewing conditions. You will need to use a colorimeter (color light meter), and provide a set of suitable source images to measure color reproduction. These tools are not provided with the projector, however, your projector supplier should be able to provide you with suitable guidance, or even an experienced professional installer.

The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you can independently adjust its range and saturation according to your preference.

If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc, you can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments.

To adjust the settings:

1.Go to the PICTURE menu and highlight 3D Color Management.

2.Press MODE/ENTER on the projector or remote control and the 3D Color Management page appears.

3.Highlight Primary Color and press / to select a color from among Red, Yellow, Green, Cyan, Blue, or Magenta.

4.Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.

28 Operation

Image 28
Contents MS504/MX505 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorTeaching Coordinate Chart Template Whiteboard Menu operationMenu system Main menu Sub-menu OptionsBasic Ceiling/Front CeilingMenu Display Sec/10 sec/20 sec/30 sec Time AlwaysAdvanced Description of each menu Apply 3D Settings Save 3D SettingsTeaching Template Description 3D Sync InvertFunction Description Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorSystem Setup Basic menu Function Description Presentation TimerInstallation SettingsLock BackgroundColor Splash ScreenSystem Setup Advanced menu Function Description Reset AllClosed CaptionSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Warranty and Copyright information Limited warrantyCopyright Disclaimer