BenQ MX505, MS504 Setting the presentation timer, Resetting current or all picture modes

Page 29

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

5.Press to highlight Saturation and adjust its values to your preference by pressing /

. Every adjustment made will reflect to the image immediately.

RED

Magenta

Yellow GREEN

Cyan

BLUE

For example, if you select Red and set its

value at 0, only the saturation of pure red will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6.Press to highlight Gain and adjust its values to your preference by pressing /

. The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7.Repeat steps 3 to 6 for other color adjustments.

8.Make sure you have made all of the desired adjustments.

9.Press MENU/EXIT to exit and save the settings.

Resetting current or all picture modes

1.Go to the PICTURE menu and highlight Reset Picture Setting.

2.Press MODE/ENTER and press / to select Current or All.

Current: returns current picture mode to the factory preset settings.

All: returns all settings, except User 1/User 2 in the PICTURE menu to the factory preset settings.

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page.

2.Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

 

Always

Displays the timer on screen throughout the presentation time.

 

3 min/2 min/1 min

Displays the timer on screen in the last 3/2/1 minute(s).

 

Never

Hides the timer throughout the presentation time.

 

 

Operation

29

Image 29
Contents MS504/MX505 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu operation Teaching Coordinate Chart Template WhiteboardMenu system Main menu Sub-menu OptionsCeiling/Front Ceiling BasicMenu Display Sec/10 sec/20 sec/30 sec Time AlwaysAdvanced Description of each menu Save 3D Settings Apply 3D SettingsTeaching Template Description 3D Sync InvertTemperature Function Description Picture ModeColor Temperature Fine Tuning 3D ColorTimer System Setup Basic menu Function Description PresentationInstallation SettingsBackground LockColor Splash ScreenReset All System Setup Advanced menu Function DescriptionClosed CaptionStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer