BenQ MX505, MS504 user manual Important safety instructions, Safety Instructions

Page 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.Please read this manual before you operate your projector. Save it for future reference.

2.Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.Refer servicing to qualified service personnel.

4.Always open the lens shutter (if any) or remove the lens cap (if any) when the projector lamp is on.

5.In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6.Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press ECO BLANK on the projector or remote control.

Important safety instructions

3

Image 3
Contents MS504/MX505 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMain menu Sub-menu Options Teaching Coordinate Chart Template WhiteboardMenu operation Menu systemTime Always BasicCeiling/Front Ceiling Menu Display Sec/10 sec/20 sec/30 secAdvanced Description of each menu 3D Sync Invert Apply 3D SettingsSave 3D Settings Teaching Template DescriptionFine Tuning 3D Color Function Description Picture ModeTemperature Color TemperatureSettings System Setup Basic menu Function Description PresentationTimer InstallationScreen LockBackground Color SplashCaption System Setup Advanced menu Function DescriptionReset All ClosedCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Disclaimer Warranty and Copyright informationLimited warranty Copyright