BenQ MS504, MX505 user manual Description of each menu

Page 38

Description of each menu

1. DISPLAY menu

	Function	Description
	Wall Color	Corrects the projected picture’s color when the projection surface is
	Wall Color	not white. See "Using Wall Color" on page 26 for details.
		not white. See "Using Wall Color" on page 26 for details.
	Aspect Ratio	There are several options to set the image's aspect ratio depending on
	Aspect Ratio	your input signal source. See "Selecting the aspect ratio" on page 24
		for details.
	Keystone	Corrects any keystoning of the image. See "Correcting keystone" on
	Keystone	page 19 for details.
		page 19 for details.
		Displays the position adjustment page. To move the projected image,
		use the directional arrow keys. The values shown on the lower
	Position	position of the page change with every key press you made until they
	Position	reach their maximum or minimum.
		reach their maximum or minimum.
		This function is only available when a PC signal (analog RGB) is selected.

		Adjusts the clock phase to reduce image
		distortion.
	Phase

This function is only available when a PC signal (analog RGB) is selected.

	H. Size	Adjusts the horizontal width of the image.
	H. Size	This function is only available when a PC signal (analog RGB) is selected.


	Digital Zoom	Magnifies or reduces the projected image. See "Magnifying and
	Digital Zoom	searching for details" on page 24 for details.
		searching for details" on page 24 for details.

38 Operation

Image 38

Contents MS504/MX505 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Teaching Coordinate Chart Template WhiteboardMenu operation Main menu Sub-menu OptionsMenu Display Sec/10 sec/20 sec/30 sec BasicCeiling/Front Ceiling Time AlwaysAdvanced Description of each menu Teaching Template Description Apply 3D SettingsSave 3D Settings 3D Sync InvertColor Temperature Function Description Picture ModeTemperature Fine Tuning 3D ColorInstallation System Setup Basic menu Function Description PresentationTimer SettingsColor Splash LockBackground ScreenClosed System Setup Advanced menu Function DescriptionReset All CaptionStatus CurrentSystem Maintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer