BenQ MX505, MS504 user manual Timing of replacing the lamp, Status Message

Page 47

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please consult your dealer or go to http://lamp.benq.com before installing a new lamp. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 49 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

 

 

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic

 

selected (See "Getting to know the lamp hour" on

Order Replacement Lamp

page 46), you may continue to operate the

Lamp>XXXX Hours

projector until the next hour lamp warning

 

appears.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Replace Lamp Soon

normal lamp behavior. You can replace the lamp

 

whenever you notice that the brightness level has

Lamp>XXXX Hours

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

Notice

 

Replace Lamp Now

 

Lamp>XXXX Hours

 

Lamp usage time exceeded

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (Refer to user manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents MS504/MX505 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMain menu Sub-menu Options Teaching Coordinate Chart Template WhiteboardMenu operation Menu systemTime Always BasicCeiling/Front Ceiling Menu Display Sec/10 sec/20 sec/30 secAdvanced Description of each menu 3D Sync Invert Apply 3D SettingsSave 3D Settings Teaching Template DescriptionFine Tuning 3D Color Function Description Picture ModeTemperature Color TemperatureSettings System Setup Basic menu Function Description PresentationTimer InstallationScreen LockBackground Color SplashCaption System Setup Advanced menu Function DescriptionReset All ClosedStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents