BenQ MS504, MX505 user manual Adjusting the sound, Using the test pattern, Muting the sound

Page 32

symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See "Connection" on page 15 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page appears.

3.Highlight Mute and press / to select On.

If available, you can also press Mute on the remote control to toggle projector audio between on and off.

Adjusting the sound level

To adjust the sound level, press Volume +/- or / , or:

1.Repeat steps 1-2 above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2 above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Using the test pattern

The projector is able to display the grid test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion.

To display the test pattern, open the OSD menu and go to the SYSTEM SETUP: Advanced > Test Pattern and press / to select On.

32 Operation

Image 32
Contents MS504/MX505 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorTeaching Coordinate Chart Template Whiteboard Menu operationMenu system Main menu Sub-menu OptionsBasic Ceiling/Front CeilingMenu Display Sec/10 sec/20 sec/30 sec Time AlwaysAdvanced Description of each menu Apply 3D Settings Save 3D SettingsTeaching Template Description 3D Sync InvertFunction Description Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorSystem Setup Basic menu Function Description Presentation TimerInstallation SettingsLock BackgroundColor Splash ScreenSystem Setup Advanced menu Function Description Reset AllClosed CaptionStatus CurrentSystem Maintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer