BenQ MS517 user manual Table of contents

Page 2

Table of contents
Important safety
instructions	3
Introduction	7
Projector features	7
Shipping contents	8
Projector exterior view	9
Positioning your
projector	15
Choosing a location	15
Obtaining a preferred projected image
size	16
Connection	18
Connecting a computer or monitor...	19
Connecting Video source devices	20
Operation	24
Starting up the projector	24
Adjusting the projected image	25
Using the menus	28
Securing the projector	29
Switching input signal	32
Magnifying and searching for details ...	33
Selecting the aspect ratio	33
Optimizing the image	35
Setting the presentation timer	39
Remote paging operations	40
Hiding the image	41
Freezing the image	41
Operating in a high altitude
environment	42
Adjusting the sound	42
Use Teaching Template	43
Personalizing the projector menu
display	44

Select the lamp saver mode	44
Shutting down the projector	45
Menu operation	46
Maintenance	58
Care of the projector	58
Lamp information	59
Troubleshooting	67
Specifications	68
Dimensions	69
Ceiling mount installation	69
Timing chart	70
Warranty and Copyright
information	74

2 Table of contents

Image 2

Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Source Volume +Setting MuteReplacing the remote control battery Front Table Positioning your projectorChoosing a location Front CeilingMS517/MX518/MS517F/MX518F Projection dimensionsObtaining a preferred projected image size MW519 762 646 404Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management Setting a preferred color temperatureAbout color temperatures Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the image Freezing the imageTo activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentUse Teaching Template Lamp Mode Description Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu displayShutting down the projector Main menu Sub-menu Options Menu operationMenu system Yes/No System Setup BasicCount Down/Count Up Normal/HighAdvanced Equivalent LampDescription of each menu 3D Sync Invert 3D ModeTeaching Template Reference Picture ModePicture menu ModeReset Picture Temperature ColorTemperature Fine Tuning 3D Color SettingSettings TimerInstallation PresentationPanel Key Basic menuOperation LockAudio System Setup Advanced menuHigh Altitude LampCaption Reset AllClosed StandbySystem Information menuCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Specifications Optical301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputCopyright Warranty and Copyright informationLimited warranty Disclaimer