BenQ MS517 user manual Presentation, Timer, Language, Projector, Installation, Menu, Settings

Page 53

FUNCTION

 

 

 

Presentation

 

4.

 

Timer

 

 

 

Basicmenu

SYSTEMSETUP:

 

Language

 

Projector

 

 

 

 

 

 

Installation

 

 

 

Menu

 

 

 

Settings

 

 

 

 

DESCRIPTION

Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 39 for details.

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 28 for details.

The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 15 for details.

Menu display Time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu Position

Sets the On-Screen Display (OSD) menu position.

Reminder message

Sets whether to display the reminder message.

Operation 53

Image 53
Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Setting Volume +Source MuteReplacing the remote control battery Choosing a location Positioning your projectorFront Table Front CeilingMS517/MX518/MS517F/MX518F Projection dimensionsObtaining a preferred projected image size 762 646 404 MW519Connection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures Setting a preferred color temperature3D Color Management Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Until the System Setup Advanced menu is highlighted Select the lamp saver modeLamp Mode Description Personalizing the projector menu displayShutting down the projector Main menu Sub-menu Options Menu operationMenu system Count Down/Count Up System Setup BasicYes/No Normal/HighEquivalent Lamp AdvancedDescription of each menu 3D Sync Invert 3D ModeTeaching Template Picture menu Picture ModeReference ModeTemperature Fine Tuning 3D Color Temperature ColorReset Picture SettingInstallation TimerSettings PresentationOperation Basic menuPanel Key LockHigh Altitude System Setup Advanced menuAudio LampClosed Reset AllCaption StandbyCurrent Information menuSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode eco function as Economic or SmartEco modeLamp information Getting to know the lamp hourPage Status Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Optical Specifications301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr inputLimited warranty Warranty and Copyright informationCopyright Disclaimer