BenQ MS517 user manual Resetting the lamp timer

Page 64

7.Tighten the screws that secure the

lamp.

• Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screws.

8.Ensure the handle is fully laid flat and

locked in place.

9.Replace the lamp cover by sliding it into place.

(a)

(b)

10.Tighten the screw that secures the lamp cover.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12.After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press Mode/Enter. The Lamp

Settings page displays. Press to highlight Reset lamp timer and press Mode/Enter.

A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

64 Maintenance

Image 64

Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Volume + SettingSource MuteReplacing the remote control battery Positioning your projector Choosing a locationFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsMS517/MX518/MS517F/MX518F MW519 762 646 404Connection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Using a security cable lock Utilizing the password functionSetting a password Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesSetting a preferred color temperature About color temperatures3D Color Management Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right How to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Hiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Select the lamp saver mode Until the System Setup Advanced menu is highlightedLamp Mode Description Personalizing the projector menu displayShutting down the projector Menu system Menu operationMain menu Sub-menu Options System Setup Basic Count Down/Count UpYes/No Normal/HighAdvanced Equivalent LampDescription of each menu Teaching Template 3D Mode3D Sync Invert Picture Mode Picture menuReference ModeTemperature Color Temperature Fine Tuning 3D ColorReset Picture SettingTimer InstallationSettings PresentationBasic menu OperationPanel Key LockSystem Setup Advanced menu High AltitudeAudio LampReset All ClosedCaption StandbyInformation menu CurrentSystem StatusMaintenance Care of the projectorSetting Lamp mode eco function as Economic or SmartEco mode Setting Auto Power OffLamp information Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Specifications OpticalCeiling mount installation Dimensions301.6 219.2 111.3 Resolution Mode Vertical Horizontal Pixel Frequency KHz MHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputWarranty and Copyright information Limited warrantyCopyright Disclaimer