BenQ MS517 user manual Indicators

Page 65

Indicators

		Light		Status & Description

	POWER	TEMP	LAMP

				Power events

	Orange	Off	Off	Stand-by mode

	Green	Off	Off	Powering up
	Flashing	Off	Off
	Flashing

	Green	Off	Off	Normal operation

	Orange	Off	Off	Normal power-down cooling
	Flashing	Off	Off
	Flashing

	Red	Off	Off	Download

	Green	Off	Red	CW start fail

	Red	Off	Off	Scaler shutdown fail (data abord)
	Flashing	Off	Off
	Flashing

	Red	Off	Red	Scaler reset fail (video projector only)

	Green	Off	Off	Burn-in ON

	Green	Green	Green	Burn-in OFF

				Lamp events

	Off	Off	Red	Lamp1 error in normal operation

	Off	Off	Red	Lamp is not lit up
	Off	Off	Flashing
			Flashing
				Thermal events

	Red	Red	Off	Fan 1 error (the actual fan speed is ±25% outside the desired
	Red	Red	Off	speed)
				speed)

	Red	Red	Off	Fan 2 error (the actual fan speed is ±25% outside the desired
	Red	Flashing	Off	speed)
		Flashing		speed)

	Red	Green	Off	Fan 3 error (the actual fan speed is ±25% outside the desired
	Red	Green	Off	speed)
				speed)

	Red	Red	Off	Temperature 1 error (over limited temperature)
	Flashing	Flashing	Off
	Flashing	Flashing

	Green	Red	Off	Thermal Sensor 1 open error
	Green	Flashing	Off
		Flashing

	Green	Green	Off	Thermal Sensor 1 short error

	Green	Green	Off	Thermal IC #1 I2C Connection error
	Green	Flashing	Off
		Flashing

	Green	Red	Off	Temperature 2 error (over limited temperature)
	Flashing	Red	Off
	Flashing

	Green	Red	Off	Thermal Sensor 2 open error
	Flashing	Flashing	Off
	Flashing	Flashing

	Green	Green	Off	Thermal Sensor 2 short error
	Flashing	Green	Off
	Flashing

Maintenance 65

Image 65

Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Setting Volume +Source MuteReplacing the remote control battery Choosing a location Positioning your projectorFront Table Front CeilingMS517/MX518/MS517F/MX518F Projection dimensionsObtaining a preferred projected image size 762 646 404 MW519Connection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures Setting a preferred color temperature3D Color Management Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Until the System Setup Advanced menu is highlighted Select the lamp saver modeLamp Mode Description Personalizing the projector menu displayShutting down the projector Main menu Sub-menu Options Menu operationMenu system Count Down/Count Up System Setup BasicYes/No Normal/HighEquivalent Lamp AdvancedDescription of each menu 3D Sync Invert 3D ModeTeaching Template Picture menu Picture ModeReference ModeTemperature Fine Tuning 3D Color Temperature ColorReset Picture SettingInstallation TimerSettings PresentationOperation Basic menuPanel Key LockHigh Altitude System Setup Advanced menuAudio LampClosed Reset AllCaption StandbyCurrent Information menuSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode eco function as Economic or SmartEco modeLamp information Getting to know the lamp hourPage Status Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Optical Specifications301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr inputLimited warranty Warranty and Copyright informationCopyright Disclaimer