BenQ MS517 user manual Connecting a Component Video source device

Page 22

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output jacks available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device. Match the color of the plugs to the color of the jacks; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER IN-1or COMPUTER IN-2jack on the projector.

3.If you wish to make use of the projector speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Source Volume +Setting MuteReplacing the remote control battery Front Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Projection dimensionsMS517/MX518/MS517F/MX518F MW519 762 646 404Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management Setting a preferred color temperatureAbout color temperatures Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right How to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Hiding the image Freezing the imageTo activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentUse Teaching Template Lamp Mode Description Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu displayShutting down the projector Menu system Menu operationMain menu Sub-menu Options Yes/No System Setup BasicCount Down/Count Up Normal/HighAdvanced Equivalent LampDescription of each menu Teaching Template 3D Mode3D Sync Invert Reference Picture ModePicture menu ModeReset Picture Temperature ColorTemperature Fine Tuning 3D Color SettingSettings TimerInstallation PresentationPanel Key Basic menuOperation LockAudio System Setup Advanced menuHigh Altitude LampCaption Reset AllClosed StandbySystem Information menuCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Specifications OpticalCeiling mount installation Dimensions301.6 219.2 111.3 Resolution Mode Vertical Horizontal Pixel Frequency KHz MHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputCopyright Warranty and Copyright informationLimited warranty Disclaimer