BenQ MS517 Picture menu, Picture Mode, Reference, Brightness, Contrast, Color, Tint, Sharpness

Page 51

2. PICTURE menu

FUNCTION

DESCRIPTION

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 35 for details.

 

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 35

 

for details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

 

page 36 for details.

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

 

See"Adjusting Contrast" on page 36 for details.

 

 

Color

Adjusts the color saturation level -- the amount of each color in a

video image. See "Adjusting Color" on page 36 for details.

 

This function is only available when a Video or S-Video signal is

 

selected.

 

 

Tint

Adjusts the red and green color tones of the image. See "Adjusting

Tint" on page 36 for details.

 

This function is only available when a Video or S-Video signal is

 

selected and the system format is NTSC.

 

 

Sharpness

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness" on page 36 for details.

 

This function is only available when a Video or S-Video signal is

 

selected.

 

 

Operation 51

Image 51
Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Mute Volume +Setting SourceReplacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Front TableProjection dimensions Obtaining a preferred projected image sizeMS517/MX518/MS517F/MX518F 762 646 404 MW519Connection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays Setting a preferred color temperatureAbout color temperatures 3D Color ManagementMagenta Cyan Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following steps How to use the Timer On key?Remote paging operations Freezing the image Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeUse Teaching Template Personalizing the projector menu display Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Lamp Mode DescriptionShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Normal/High System Setup BasicCount Down/Count Up Yes/NoEquivalent Lamp AdvancedDescription of each menu 3D Mode Teaching Template3D Sync Invert Mode Picture ModePicture menu ReferenceSetting Temperature ColorTemperature Fine Tuning 3D Color Reset PicturePresentation TimerInstallation SettingsLock Basic menuOperation Panel KeyLamp System Setup Advanced menuHigh Altitude AudioStandby Reset AllClosed CaptionStatus Information menuCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Optical SpecificationsDimensions Ceiling mount installation301.6 219.2 111.3 Timing chart Resolution Mode Vertical Horizontal Pixel Frequency KHz MHzSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr inputDisclaimer Warranty and Copyright informationLimited warranty Copyright