BenQ MS517 user manual Remote control

Page 12

Remote control

1

11

 

12

2

13

 

3

3

4

 

5

14

 

12

6

 

 

15

7

 

 

16

 

17

8

18

 

 

19

9

20

10

21

 

22

1.Info

Showing the status information of the projector.

2.Menu/Exit

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

See "Using the menus" on page 28 for details.

3. Left/ Right

When the On-Screen Display (OSD) menu is activated, the #3 and #12 keys are used as directional arrows to select the desired menu items and to make adjustments. See "Using the menus" on page 28 for details.

4.Mode/Enter

Selects an available picture setup mode. See "Selecting a picture mode" on page 35 for details.

Activates the selected On-Screen Display (OSD) menu item. See "Using the menus" on page 28 for details.

5.Eco Blank

Press the Eco Blank button to turn off the image for a period of time with 70% lamp power saving. Press again to restore the image. See "Hiding the image" on page 41 for details.

6.SmartEco

Displays the lamp mode selection bar(Normal/Economic/SmartEco).

7.Aspect

Selects the display aspect ratio. See "About the aspect ratio" on page 34 for details.

8.Digital Zoom keys (+, -) Magnifies or reduces the projected picture size. See "Magnifying and searching for details" on page 33 for details.

9.Timer On

Activates or displays an on-screen timer based on your own timer setting. See "Setting the presentation timer" on page 39 for details.

10.Timer Setup

Enters presentation timer setting directly. See "Setting the presentation timer" on page 39 for details.

11.II Power

Toggles the projector between standby mode and on. See "Starting up the projector" on page 24 and "Shutting down the projector" on page 45 for details.

12.Keystone/Arrow keys ( / Up,

/ Down)

Manually corrects distorted images resulting from an angled projection. See "Correcting keystone" on page 27 for details.

13.Auto

Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 25 for details.

12 Introduction

Image 12
Contents MS517/MX518/MW519/MS517F/MX518F Digital Projector Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Volume + SettingSource MuteReplacing the remote control battery Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeMS517/MX518/MS517F/MX518F MW519 762 646 404Connection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Using a security cable lock Utilizing the password functionSetting a password Securing the projectorIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesSetting a preferred color temperature About color temperatures3D Color Management Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following steps How to use the Timer On key?Remote paging operations Hiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Select the lamp saver mode Until the System Setup Advanced menu is highlightedLamp Mode Description Personalizing the projector menu displayShutting down the projector Menu operation Menu systemMain menu Sub-menu Options System Setup Basic Count Down/Count UpYes/No Normal/HighAdvanced Equivalent LampDescription of each menu 3D Mode Teaching Template3D Sync Invert Picture Mode Picture menuReference ModeTemperature Color Temperature Fine Tuning 3D ColorReset Picture SettingTimer InstallationSettings PresentationBasic menu OperationPanel Key LockSystem Setup Advanced menu High AltitudeAudio LampReset All ClosedCaption StandbyInformation menu CurrentSystem StatusMaintenance Care of the projectorSetting Lamp mode eco function as Economic or SmartEco mode Setting Auto Power OffLamp information Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Troubleshooting Specifications OpticalDimensions Ceiling mount installation301.6 219.2 111.3 Timing chart Resolution Mode Vertical Horizontal Pixel Frequency KHz MHzSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputWarranty and Copyright information Limited warrantyCopyright Disclaimer