BenQ CP120 manual Connecting a Component Video source device

Page 26

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device

1.Take the (optional accessory) Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with

a D-Sub type connector) to the D-SUB/COMP IN socket on the projector. The final connection path should be like that shown in the following diagram:

Component Video to VGA (D-Sub) adaptor cable

A/V device

Component Video is the only video output that delivers native 16:9 aspect ratio picture.

If you connect the projector to a High Definition TV (HDTV) tuner, the following standards are supported:

480i

480p

576i

576p

720p (50/ 60 Hz)

1080i (50/ 60 Hz)

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

18 Connection

Image 26
Contents Welcome Software license agreement CopyrightDisclaimer Copyright Memo Table of Contents Fine-tuning the image size and clarity Iv Table of ContentsDimensions Timing chart Table of ContentsMemo Vi Table of Contents Important safety instructions Important safety instructionsBut could fail if power cuts or surges Safety instructions Bedding or any other soft surface Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Other itemSafety instructions Introduction Projector featuresIntroduction Shipping contents Rear side Projector exterior viewFront / Upper side Lower sideTurns the projector on or off Introduction Controls and functionsExternal control panel Adjusts the focus of the projected image Press this button to display the Wireless Connection menu Remote control descriptionDown on the remote control Turns the projector on or offRemote control effective range Installing or replacing the remote control batteryObtaining a preferred projected image size Positioning your projectorChoosing a location EquipmentSelect your screen size Positioning your projector Screen Center of lens Projection distance Screen size chartMaximum Minimum Zoom Connection Connecting a computerConnection Connecting Video source devices Best video qualityConnecting a Component Video source device Component Video to VGA D-Sub adaptor cable DeviceConnecting an S-Video source device Video cable DeviceConnecting a composite Video source device Using the projector Using the projectorSwitch all of the connected equipment on Start upUtilizing the password function To set a passwordTo change the password If you forget the passwordTo enter the password recall procedure Fine-tuning the image size and clarity Adjusting the heightAuto-adjusting the image That you need using the zoom ring Focus ringRight buttons on Correcting keystoneManual keystone correction Hiding the image Selecting an application modeSwitching input signal Automatic keystone correctionFreezing the image Disconnect the power cord from the wall socketRemote paging operations ShutdownHardware and software requirements Using the wireless functionsAbout wireless connection modes and channels Preparing your computer for wireless connection Checking the TCP/IP settings of your computerMaking wireless presentation Installing Wireless WizardClick to select a wireless network card from the list Current wireless connection channel Page Controlling presentation Freezing imageDisconnecting Method 2 Projector controlMenu operation Menu systemUsing the menus Picture menu Color Temp Selected Application ModeKeystone Depends onPro-Picture menu Setting menu Advance menu Economic Turned off. Selecting Off disables this functionAuto Off Off Periods of time 10hours without shutdownInformation Menu ResolutionMode Equivalent SourceMaintenance Care of the projectorCalculation of lamp hour Message StatusReplacing the lamp Temperature information Resetting the lamp counterStand-by mode IndicatorsProjector needs to cool after the power is Turned off Powering upMaintenance No picture TroubleshootingProjector does not turn on Image is unstableConfigured Remote control does not workUnable to use wireless connection NearbySpecifications Projector specificationsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz DimensionsTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Component-YPbPrInput Warranty WarrantyLimited warranty EEC statement Regulation statementsFCC statement MIC statementMemo Regulation statements