BenQ CP120 manual Regulation statements, FCC statement, EEC statement, MIC statement

Page 65

Regulation statements

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the distance between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

EEC statement

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic Magnetic Compatibility) and fulfills these requirements.

MIC statement

B class equipment (Household purpose info/telecommunications equipment)

As this equipment has undergone EMC registration for household purpose, this product can be used in any area including residential area.

Regulation statements

57

Image 65

Contents Welcome Software license agreement CopyrightDisclaimer Copyright Memo Table of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Dimensions Timing chartMemo Vi Table of Contents Important safety instructions Important safety instructionsBut could fail if power cuts or surges Safety instructions Following environments Do not place this unit on a blanket Do not block the ventilation holesBedding or any other soft surface Other itemSafety instructions Introduction Projector featuresIntroduction Shipping contents Front / Upper side Projector exterior viewRear side Lower sideTurns the projector on or off Introduction Controls and functionsExternal control panel Adjusts the focus of the projected image Down on the remote control Remote control descriptionPress this button to display the Wireless Connection menu Turns the projector on or offInstalling or replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size EquipmentSelect your screen size Positioning your projector Screen Center of lens Projection distance Screen size chartMaximum Minimum Zoom Connection Connecting a computerConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Switch all of the connected equipment on Using the projectorUsing the projector Start upTo set a password Utilizing the password functionTo change the password If you forget the passwordTo enter the password recall procedure Auto-adjusting the image Adjusting the heightFine-tuning the image size and clarity That you need using the zoom ring Focus ringRight buttons on Correcting keystoneManual keystone correction Switching input signal Selecting an application modeHiding the image Automatic keystone correctionRemote paging operations Disconnect the power cord from the wall socketFreezing the image ShutdownHardware and software requirements Using the wireless functionsAbout wireless connection modes and channels Checking the TCP/IP settings of your computer Preparing your computer for wireless connectionInstalling Wireless Wizard Making wireless presentationClick to select a wireless network card from the list Current wireless connection channel Page Freezing image Controlling presentationMethod 2 Projector control DisconnectingMenu system Menu operationUsing the menus Picture menu Keystone Selected Application ModeColor Temp Depends onPro-Picture menu Setting menu Advance menu Auto Off Off Turned off. Selecting Off disables this functionEconomic Periods of time 10hours without shutdownMode Equivalent ResolutionInformation Menu SourceCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationProjector needs to cool after the power is Turned off IndicatorsStand-by mode Powering upMaintenance Projector does not turn on TroubleshootingNo picture Image is unstableUnable to use wireless connection Remote control does not workConfigured NearbyProjector specifications SpecificationsTiming chart DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC inputSupported timing for Video and S-Video inputs Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Component-YPbPrInput Warranty WarrantyLimited warranty FCC statement Regulation statementsEEC statement MIC statementMemo Regulation statements