BenQ CP120 manual Connecting an S-Video source device, Video cable Device

Page 27

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device

1.Take an appropriate S-Video cable (not supplied) and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEO socket on the projector. The final connection path should be like that shown in the following diagram:

S-Video cable

A/V device

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S- Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 17 for details.

Connection 19

Image 27

Contents Welcome Copyright DisclaimerSoftware license agreement Copyright Memo Table of Contents Iv Table of Contents Fine-tuning the image size and clarityTable of Contents Dimensions Timing chartMemo Vi Table of Contents Important safety instructions But could fail if power cuts or surgesImportant safety instructions Safety instructions Other item Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Bedding or any other soft surfaceSafety instructions Projector features IntroductionIntroduction Shipping contents Lower side Projector exterior viewFront / Upper side Rear sideControls and functions External control panelTurns the projector on or off Introduction Adjusts the focus of the projected image Turns the projector on or off Remote control descriptionDown on the remote control Press this button to display the Wireless Connection menuInstalling or replacing the remote control battery Remote control effective rangeEquipment Positioning your projectorChoosing a location Obtaining a preferred projected image sizeSelect your screen size Positioning your projector Screen size chart Maximum Minimum ZoomScreen Center of lens Projection distance Connecting a computer ConnectionConnection Best video quality Connecting Video source devicesComponent Video to VGA D-Sub adaptor cable Device Connecting a Component Video source deviceVideo cable Device Connecting an S-Video source deviceConnecting a composite Video source device Start up Using the projectorSwitch all of the connected equipment on Using the projectorTo set a password Utilizing the password functionIf you forget the password To enter the password recall procedureTo change the password That you need using the zoom ring Focus ring Adjusting the heightAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Manual keystone correctionRight buttons on Automatic keystone correction Selecting an application modeSwitching input signal Hiding the imageShutdown Disconnect the power cord from the wall socketRemote paging operations Freezing the imageUsing the wireless functions About wireless connection modes and channelsHardware and software requirements Checking the TCP/IP settings of your computer Preparing your computer for wireless connectionInstalling Wireless Wizard Making wireless presentationClick to select a wireless network card from the list Current wireless connection channel Page Freezing image Controlling presentationMethod 2 Projector control DisconnectingMenu system Menu operationUsing the menus Picture menu Depends on Selected Application ModeKeystone Color TempPro-Picture menu Setting menu Advance menu Periods of time 10hours without shutdown Turned off. Selecting Off disables this functionAuto Off Off EconomicSource ResolutionMode Equivalent Information MenuCare of the projector MaintenanceMessage Status Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature informationPowering up IndicatorsProjector needs to cool after the power is Turned off Stand-by modeMaintenance Image is unstable TroubleshootingProjector does not turn on No pictureNearby Remote control does not workUnable to use wireless connection ConfiguredProjector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSignal Format Horizontal Frequency Vertical Frequency KHz Supported timing for Component-YPbPrInputSupported timing for Video and S-Video inputs Warranty Limited warrantyWarranty MIC statement Regulation statementsFCC statement EEC statementMemo Regulation statements