BenQ CP120 manual Connecting a composite Video source device

Page 28

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an composite Video source device

1.Take an appropriate Video cable (not supplied) and connect one end to the composite Video output socket of the Video source device.

2.Connect the other end of the Video cable to the VIDEO socket on the projector.

The final connection path should be like that shown in the following diagram:

Video cable

A/V device

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are unavailable for use. See "Connecting Video source devices" on page 17 for details.

20 Connection

Image 28

Contents Welcome Disclaimer CopyrightSoftware license agreement Copyright Memo Table of Contents Fine-tuning the image size and clarity Iv Table of ContentsDimensions Timing chart Table of ContentsMemo Vi Table of Contents But could fail if power cuts or surges Important safety instructionsImportant safety instructions Safety instructions Do not block the ventilation holes Following environments Do not place this unit on a blanketBedding or any other soft surface Other itemSafety instructions Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front / Upper sideRear side Lower sideExternal control panel Controls and functionsTurns the projector on or off Introduction Adjusts the focus of the projected image Remote control description Down on the remote controlPress this button to display the Wireless Connection menu Turns the projector on or offRemote control effective range Installing or replacing the remote control batteryPositioning your projector Choosing a locationObtaining a preferred projected image size EquipmentSelect your screen size Positioning your projector Maximum Minimum Zoom Screen size chartScreen Center of lens Projection distance Connection Connecting a computerConnection Connecting Video source devices Best video qualityConnecting a Component Video source device Component Video to VGA D-Sub adaptor cable DeviceConnecting an S-Video source device Video cable DeviceConnecting a composite Video source device Using the projector Switch all of the connected equipment onUsing the projector Start upUtilizing the password function To set a passwordTo enter the password recall procedure If you forget the passwordTo change the password Adjusting the height Auto-adjusting the imageFine-tuning the image size and clarity That you need using the zoom ring Focus ringManual keystone correction Correcting keystoneRight buttons on Selecting an application mode Switching input signalHiding the image Automatic keystone correctionDisconnect the power cord from the wall socket Remote paging operationsFreezing the image ShutdownAbout wireless connection modes and channels Using the wireless functionsHardware and software requirements Preparing your computer for wireless connection Checking the TCP/IP settings of your computerMaking wireless presentation Installing Wireless WizardClick to select a wireless network card from the list Current wireless connection channel Page Controlling presentation Freezing imageDisconnecting Method 2 Projector controlMenu operation Menu systemUsing the menus Picture menu Selected Application Mode KeystoneColor Temp Depends onPro-Picture menu Setting menu Advance menu Turned off. Selecting Off disables this function Auto Off OffEconomic Periods of time 10hours without shutdownResolution Mode EquivalentInformation Menu SourceMaintenance Care of the projectorCalculation of lamp hour Message StatusReplacing the lamp Temperature information Resetting the lamp counterIndicators Projector needs to cool after the power is Turned offStand-by mode Powering upMaintenance Troubleshooting Projector does not turn onNo picture Image is unstableRemote control does not work Unable to use wireless connectionConfigured NearbySpecifications Projector specificationsDimensions Timing chartHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC inputSupported timing for Component-YPbPrInput Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Video and S-Video inputs Limited warranty WarrantyWarranty Regulation statements FCC statementEEC statement MIC statementMemo Regulation statements