BenQ CP120 manual Making wireless presentation, Installing Wireless Wizard

Page 38

4.Make sure that Obtain an IP address automatically and Obtain DNS server address automatically are selected, and then click the OK button.

Installing Wireless Wizard

In order to get your computer ready for wireless connection to the projector, you need to install Wireless Wizard.

Pre-installation check

1.Check that your system meets the system requirements for operating system and hardware requirements described above.

2.Ensure you have sufficient privileges to install software.

3.Ensure you have uninstalled any previously installed Wireless Wizard.

Installation

1.Close any other applications being run.

2.Insert the projector software CD into the CD drive of your computer. The software installation menu will display on-screen.

If installation does not begin automatically, browse the CD using Windows Explorer and double-click Setup.exe to begin installation.

3.Click Install Wireless Wizard and follow the on-screen instructions to proceed.

4.Restart your computer after you complete the installation.

5.After Wireless Wizard is successfully installed, the shortcut icon will be created on the Desktop.

Making wireless presentation

1.Make sure that the distance between the computer(s) and projector is within 10 meters (32 feet).

2.Start up the projector and press the Source (or SOURCE/WIRELESS) button to switch the input source to Wireless. Refer to "Switching input signal" on page 26 for more information.

30 Using the projector

Image 38

Contents Welcome Software license agreement CopyrightDisclaimer Copyright Memo Table of Contents Fine-tuning the image size and clarity Iv Table of ContentsDimensions Timing chart Table of ContentsMemo Vi Table of Contents Important safety instructions Important safety instructionsBut could fail if power cuts or surges Safety instructions Bedding or any other soft surface Do not block the ventilation holesFollowing environments Do not place this unit on a blanket Other itemSafety instructions Introduction Projector featuresIntroduction Shipping contents Rear side Projector exterior viewFront / Upper side Lower sideTurns the projector on or off Introduction Controls and functionsExternal control panel Adjusts the focus of the projected image Press this button to display the Wireless Connection menu Remote control descriptionDown on the remote control Turns the projector on or offRemote control effective range Installing or replacing the remote control batteryObtaining a preferred projected image size Positioning your projectorChoosing a location EquipmentSelect your screen size Positioning your projector Screen Center of lens Projection distance Screen size chartMaximum Minimum Zoom Connection Connecting a computerConnection Connecting Video source devices Best video qualityConnecting a Component Video source device Component Video to VGA D-Sub adaptor cable DeviceConnecting an S-Video source device Video cable DeviceConnecting a composite Video source device Using the projector Using the projectorSwitch all of the connected equipment on Start upUtilizing the password function To set a passwordTo change the password If you forget the passwordTo enter the password recall procedure Fine-tuning the image size and clarity Adjusting the heightAuto-adjusting the image That you need using the zoom ring Focus ringRight buttons on Correcting keystoneManual keystone correction Hiding the image Selecting an application modeSwitching input signal Automatic keystone correctionFreezing the image Disconnect the power cord from the wall socketRemote paging operations ShutdownHardware and software requirements Using the wireless functionsAbout wireless connection modes and channels Preparing your computer for wireless connection Checking the TCP/IP settings of your computerMaking wireless presentation Installing Wireless WizardClick to select a wireless network card from the list Current wireless connection channel Page Controlling presentation Freezing imageDisconnecting Method 2 Projector controlMenu operation Menu systemUsing the menus Picture menu Color Temp Selected Application ModeKeystone Depends onPro-Picture menu Setting menu Advance menu Economic Turned off. Selecting Off disables this functionAuto Off Off Periods of time 10hours without shutdownInformation Menu ResolutionMode Equivalent SourceMaintenance Care of the projectorCalculation of lamp hour Message StatusReplacing the lamp Temperature information Resetting the lamp counterStand-by mode IndicatorsProjector needs to cool after the power is Turned off Powering upMaintenance No picture TroubleshootingProjector does not turn on Image is unstableConfigured Remote control does not workUnable to use wireless connection NearbySpecifications Projector specificationsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz DimensionsTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Component-YPbPrInput Warranty WarrantyLimited warranty EEC statement Regulation statementsFCC statement MIC statementMemo Regulation statements