BenQ mw814st user manual Remote control

Page 11

Remote control

7

1

8

2 9

3	10
3
4	11
5	12
	8
6	13
6
	14
	15

1. POWER

Toggles the projector between standby mode and on.

2. Freeze

Freezes the projected image.

3. Left

4.BLANK

Used to hide the screen picture.

5.Digital Zoom (+, -)

Magnifies or reduces the projected picture size.

6.Volume +/-

Adjusts the sound level.

7.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

8.Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

9.Auto

Automatically determines the best picture timings for the displayed image.

10. Right

When the On-Screen Display (OSD) menu is activated, the #3, #8, and #10 keys are used as directional arrows to select the desired menu items and to make adjustments.

11.SOURCE

Displays the source selection bar.

12.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

13.Timer On

Activates or displays an on-screen timer based on your own timer setting.

14.Timer Set up

Enters presentation timer setting directly.

15.PAGE UP/PAGE DOWN

Operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

Introduction 11

Image 11

Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Front Table996 1771 866 Projection dimensionsObtaining a preferred projected image size Diagonal Height Width From screen Offset Inches 2032B1 a 150 3810 2019 3231 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 120 3048 1615 2585Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation OperationStarting up the projector Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature 3D Color Management Save SettingsColor Space TimerSettings SearchLock Function DescriptionOperation Panel KeyLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyStatus Information menu Function DescriptionCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installationWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright