BenQ mw814st user manual Safety Instructions

Page 4

Safety Instructions (Continued)

7.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

8.Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

9.Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

11.Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

12.When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

4 Important safety instructions

Image 4

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeDiagonal Height Width From screen Offset Inches 2032 996 1771 866B1 a 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787 100 2540 1346 2154120 3048 1615 2585 150 3810 2019 3231Connection Connecting video source devices Connecting audioTerminal name Terminal appearance BestStarting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Picture Mode Temperature 3D ColorManagement Save Settings Display menu Picture menu Function Description TeachingTimer SettingsSearch Color SpaceFunction Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsCeiling Minimum Ceiling Height mm = f + H + b + 60 + 274+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer