BenQ mw814st Indicators, Light Status & Description Power events, Lamp events, Thermal events

Page 56

Indicators

Light

Status & Description

					Power events

	Off	Off	Orange	Stand-by mode.
	Off	Off	FlashingGreen	Powering up.
	Off	Off	Green	Normal operation.
				• The projector needs 90 seconds to cool down as it was
					abnormally shut down without the normal cooling down
					process.
	Off	Off	Orange	• The projector needs to cool for 90 seconds after the power
	Off	Off	Flashing		is turned off.
			Flashing		is turned off.
				• The projector has shut down automatically. If you try to re-
					start the projector, it will shut down again. Please contact
					your dealer for assistance.

					Lamp events
	Red	Off	Orange	The projector has shut down automatically. If you try to re-
	Red	Off	Flashing	start the projector, it will shut down again. Please contact your
				dealer for assistance.
	Red	Off	Off	1.	The projector needs 90 seconds to cool down. Or
	Red	Off	Off	2.	Please contact your dealer for assistance.
				2.	Please contact your dealer for assistance.

Thermal events

Off	Red	Off
Red	Red	Off
Green	Red	Off
Orange	Red	Off
Red	Red	Red
Green	Red	Red
Orange	Red	Red
Red	Red	Green
Green	Red	Green
Orange	Red	Green
Red	Red	Orange
Green	Red	Orange
Orange	Red	Orange
Red	Green	Off
Green	Green	Off

The projector has shut down automatically. If you try to re- start the projector, it will shut down again. Please contact your dealer for assistance.

56 Maintenance

Image 56

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeDiagonal Height Width From screen Offset Inches 2032 996 1771 866B1 a 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787 100 2540 1346 2154120 3048 1615 2585 150 3810 2019 3231Connection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysCreating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Picture Mode Temperature 3D ColorManagement Save Settings Display menu Picture menu Function Description TeachingTimer SettingsSearch Color SpaceFunction Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer