BenQ mw814st user manual Advanced

Page 42

	Main menu Sub-menu			Options

		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
			Lamp Mode	Normal/Economic
		Lamp Settings	Reset Lamp Timer
			Equivalent Lamp Hour
		Security	Change Password
		Security	Change Security	Power On Lock
		Settings	Change Security	Power On Lock
		Settings	Settings	Splash Screen Lock
			Settings	Splash Screen Lock
		Baud Rate		2400/4800/9600/14400/19200/
		Baud Rate		38400/57600/115200
				38400/57600/115200
	5.	Test Pattern		On/Off
	5.		Closed Caption	On/Off
	SYSTEM	Closed Caption	Enable	On/Off
	SYSTEM	Closed Caption	Enable
	SETUP:
	SETUP:		Caption Version	CC1/CC2/CC3/CC4
	Advanced		Network	On/Off
		Standby	Monitor Out	On/Off
		Settings	Audio Pass	Off/Computer 1/Computer 2/
			Through	Video,S-Video/HDMI
				Status
				DHCP
				IP Address
			Wired LAN	Subnet Mask
		Network		Default Gateway
		Settings		DNS Server
				Apply
			AMX Device	On/Off
			Discovery	On/Off
			Discovery
			Mac Address

	Reset All Settings
		•	Source
		•	Picture Mode
6.	Current System Status	•	Resolution
INFORMATION	Current System Status	•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

42 Operation

Image 42

Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Front Table Positioning your projectorChoosing a location Front CeilingDiagonal Height Width From screen Offset Inches 2032 Projection dimensionsObtaining a preferred projected image size 996 1771 866B1 a 120 3048 1615 2585 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 150 3810 2019 3231Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Adjusting the sound Controlling the projector through a LAN environmentCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Management Save Settings Picture ModeTemperature 3D Color Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsMinimum Ceiling Height mm = f + H + b + 60 + 274+ c CeilingWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer