BenQ mw814st user manual Minimum Ceiling Height mm = f + H + b + 60 + 274+ c, Wall plate

Page 61

Minimum Ceiling Height (mm) = f + H + b + 60 + 274+ c

c		Ceiling
60
274		a
b		232.6
H	screen	D
		D

		W

fDistance from floor to bottom of image

floor

e

Projection area

20 60

				150	180
				150	180

Wall plate

• The dimensions are based on the BenQ wall mount (P/N: 5J.J4R10.001).

•There is 3% tolerance among these numbers due to optical component variations. BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

•The dimensions supplied are offered as a guide only and may differ depending on several factors relating to any specific installation.

•The dimensions are based on the projector being configured with zero keystone correction.

•The dimensions assume that the wall mount arm is positioned 90° from the bottom case of projector and screen surface.

Specifications 61

Image 61

Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsDiagonal Height Width From screen Offset Inches 2032 996 1771 866B1 a 100 2540 1346 2154 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787120 3048 1615 2585 150 3810 2019 3231Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionFreezing the image Remote paging operationsHiding the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Temperature 3D Color Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingSettings TimerSearch Color SpaceOperation Function DescriptionPanel Key LockAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installationCeiling Minimum Ceiling Height mm = f + H + b + 60 + 274+ cWall plate Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright Disclaimer