BenQ mw814st user manual Using the menus, Following example describes how to set the OSD language

Page 22

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Sub-menu

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

Highlight

Teaching Template

Current input signal

Analog RGB

Off

Auto

ENTER

0

0

Off

Disable

MENU Exit

Status

Press MENU/ EXIT to the previous page or to exit.

The following example describes how to set the OSD language.

1.Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone
Position
Phase	0
H. Size	0
Digital Zoom
3D Sync	Off
3D Sync Invert	Disable
Teaching Template
Analog RGB	MENU Exit

3.Press to highlight Language

and press / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Off
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen

4.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB	MENU Exit

22 Operation

Image 22

Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Front Table Positioning your projectorChoosing a location Front CeilingDiagonal Height Width From screen Offset Inches 2032 Projection dimensionsObtaining a preferred projected image size 996 1771 866B1 a 120 3048 1615 2585 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 150 3810 2019 3231Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestStarting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Management Save Settings Picture ModeTemperature 3D Color Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsCeiling Minimum Ceiling Height mm = f + H + b + 60 + 274+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer