BenQ mw814st user manual Specifications, Projector specifications

Page 58

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1280 x 800 WXGA

Display system 1-CHIP DMD

Lens F/Number

F = 2.59 Lamp

220 W lamp

Electrical

Power supply

AC100–240V, 3.3 A, 50-60 Hz (Automatic) Power consumption

295 W (Max); < 1 W (Standby)

Mechanical

Weight

2.7 Kg (5.9 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 10 watt x 1 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 2

USB port (Mini-B x 1)

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI V1.3 x 1

Audio signal input Audio in

PC audio jack x 2

RCA audio jack (L/R) x 2

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

58 Specifications

Image 58

Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Front Table Positioning your projectorChoosing a location Front CeilingDiagonal Height Width From screen Offset Inches 2032 Projection dimensionsObtaining a preferred projected image size 996 1771 866B1 a 120 3048 1615 2585 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 150 3810 2019 3231Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestStarting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Management Save Settings Picture ModeTemperature 3D Color Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsCeiling Minimum Ceiling Height mm = f + H + b + 60 + 274+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer