BenQ mw814st user manual Connection

Page 17

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

•In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.

•The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model.

Notebook or desktop computer

Monitor

A/V device

(VGA)		(DVI)
	2	3							7	8	Speakers	9

1			1	9	4	5	9	6
1			1	9	4	5	9	6

1.VGA cable

2.VGA to DVI-A cable

3.USB cable

4.HDMI cable

5.Component Video to VGA (D-Sub) adapter cable

6.Audio L/R cable

7.S-Video cable

8.Video cable

9.Audio cable

Connection 17

Image 17

Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsDiagonal Height Width From screen Offset Inches 2032 996 1771 866B1 a 100 2540 1346 2154 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787120 3048 1615 2585 150 3810 2019 3231Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestOperation OperationStarting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionFreezing the image Remote paging operationsHiding the image Locking control keysCreating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Temperature 3D Color Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingSettings TimerSearch Color SpaceOperation Function DescriptionPanel Key LockAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installationWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright Disclaimer