BenQ mw814st Display menu Picture menu Function Description Teaching, Template, Picture Mode

Page 44

1. DISPLAY menu

2. PICTURE menu

Function

Description

Teaching

Provides several preset patterns for various teaching purposes.

Choose Blackboard or Whiteboard first by pressing /

and press

Template

/ to choose the pattern you need. Press MODE/ENTER to activate

 

the pattern.

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 29 for details.

 

 

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 29 for

 

details.

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on page

30 for details.

 

 

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 30 for details.

 

 

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a video

Color

image. See "Adjusting Color" on page 30 for details.

 

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

 

Adjusts the red and green color tones of the image. See "Adjusting Tint"

Tint

on page 30 for details.

 

This function is only available when a Video or S-Video signal is

 

 

selected and the system format is NTSC.

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 30 for details.

 

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

Brilliant Color

See "Adjusting Brilliant Color" on page 30 for details.

 

 

 

 

Color

See "Selecting a color temperature" on page 30 for details.

 

Temperature

 

 

 

 

 

 

3D Color

See "3D Color Management" on page 31 for details.

 

Management

 

 

 

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

44 Operation

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeDiagonal Height Width From screen Offset Inches 2032 996 1771 866B1 a 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787 100 2540 1346 2154120 3048 1615 2585 150 3810 2019 3231Connection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysCreating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Picture Mode Temperature 3D ColorManagement Save Settings Display menu Picture menu Function Description TeachingTimer SettingsSearch Color SpaceFunction Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirementsWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer
Top Page Image Contents