BenQ mw814st user manual Magnifying and searching for details, Selecting the aspect ratio

Page 27

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

•Using the remote control

1.Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

2.Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

3.To restore the picture to its original size, press Auto. You can also press Digital Zoom-. When the key is pressed again, the picture is further reduced until it is restored to the original size.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.

3.Press repeatedly to magnify the picture to a desired size.

4.To navigate the picture, press MODE/ENTER to switch to the panning mode and press

the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

5.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out function, and press Auto to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected picture ratio (no matter what aspect the source is):

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Aspect Ratio.

3.Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

Operation 27

Image 27

Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideRear/lower side Projector Controls and functionsRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Front Ceiling Positioning your projectorChoosing a location Front Table996 1771 866 Projection dimensionsObtaining a preferred projected image size Diagonal Height Width From screen Offset Inches 2032B1 a 150 3810 2019 3231 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 120 3048 1615 2585Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation Starting up the projectorOperation Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Adjusting the sound Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature 3D Color Management Save SettingsColor Space TimerSettings SearchLock Function DescriptionOperation Panel KeyLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyStatus Information menu Function DescriptionCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 274+ c CeilingWall plate Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright