BenQ MX613ST Remote control effective range, Replacing the remote control battery, Approx.+15º

Page 12

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the top of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

• Operating the projector from the front • Operating the projector from the top

Capture

Approx.+15º

Capture

	º
ox.	+15
Appr

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2. Insert the new battery in the holder. Note the positive polarity should face outward.

3.Push the holder into the remote control.

• Avoid excessive heat and humidity.

• There may be battery damage if the battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used battery according to the battery

manufacturer's instructions.

•Never throw a battery into a fire. There may be danger of an explosion.

•If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

12 Introduction

Image 12

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Volume + Timer OnTimer Set up FreezeRemote control effective range Replacing the remote control batteryPull out the battery holder Approx.+15ºPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageOn the remote control or projector for To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundWireless connection Controlling the projector through a LAN environmentPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description 3D SyncSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key BackgroundLock SplashSystem Setup Advanced menu Function Description WirelessReset All Baud RateFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive