BenQ MS612ST Confined. Allow at least 50 cm clearance, If the ventilation holes are seriously

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the 14. Do not block the ventilation holes.

following environments.

- Do not place this projector on a blanket,

- Space that is poorly ventilated or

bedding or any other soft surface.

- Do not cover this projector with a cloth

confined. Allow at least 50 cm clearance

from walls and free flow of air around

or any other item.

the projector.

- Do not place inflammables near the

- Locations where temperatures may

projector.

become excessively high, such as the

 

inside of a car with all windows rolled

 

up.

 

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

 

If the ventilation holes are seriously

 

obstructed, overheating inside the

 

projector may result in a fire.

15.

Always place the projector on a level,

 

horizontal surface during operation.

 

- Do not use if tilted at an angle of more

- Locations near fire alarms

than 10 degrees left to right, nor at angle

- Locations with an ambient temperature

of more than 15 degrees front to back.

above 40°C / 104°F

Using the projector when it is not fully

- Locations where the altitudes are higher

horizontal may cause a malfunction of,

or damage to, the lamp.

than 3000 m (10000 feet).

 

3000 m

 

(10000 feet)

 

16.

Do not stand the projector on end

0 m

vertically. Doing so may cause the

(0 feet)

projector to fall over, causing injury or

 

resulting in damage to the projector.

Important safety instructions

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer On Volume +Timer Set up FreezeReplacing the remote control battery Remote control effective rangePull out the battery holder Approx.+15ºChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestOperation OperationStarting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageTo activate the High Altitude Mode On the remote control or projector forLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Wireless connectionPage Page Page Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Page Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchBackground Panel KeyLock SplashWireless System Setup Advanced menu Function DescriptionReset All Baud RateCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive
Top Page Image Contents